GENERATOR INSTALLATION

INSTALL GENERATOR
1. Install the generator with the bolt.
  
  Torque:
  
  62 N*m { 632 kgf*cm, 46 ft.*lbf }
2. Install the generator wire to terminal B with the nut.
  
  Torque:
  
  9.8 N*m { 100 kgf*cm, 7.2 ft.*lbf }
3. Install the terminal cap.
4. Connect the generator connector.
INSTALL GENERATOR BRACKET
1. Install the generator bracket with the 2 bolts.
  
  Torque:
  
  36 N*m { 367 kgf*cm, 27 ft.*lbf }
INSTALL NO. 2 IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)
1. Install the No.2 idle pulley assembly and washer with the bolt.
  
  Torque:
  
  45 N*m { 459 kgf*cm, 33 ft.*lbf }
INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
1. Provisionally tighten the compressor and magnetic clutch with the 4 bolts.
2. Tighten the compressor and magnetic clutch with the 4 bolts.
  
  Torque:
  
  25 N*m { 255 kgf*cm, 18 ft.*lbf }
  
  Note
  
  Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.
INSTALL FAN & GENERATOR V BELT
1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
  
  Note
  
  Make sure that the fan and generator V belt is set properly on each pulley.
2. Check that the indicator mark of the V-ribbed belt tensioner Click here.
INSTALL AIR TUBE ASSEMBLY
1. Install the air tube assembly with the 2 hose clamps and 2 bolts.
  
  Torque:
  
  18 N*m { 180 kgf*cm, 13 ft.*lbf, for bolt A }
  
  7.0 N*m { 71 kgf*cm, 62 in.*lbf, for bolt B }
INSTALL NO. 1 AIR CLEANER HOSE
1. Install the air cleaner hose to the compressor inlet elbow.
  
  Note
  
  Pull the hose to make sure that it is locked and securely connected.
INSTALL COMPRESSOR OUTLET ELBOW
1. Install the compressor outlet elbow with the 2 hose clamps and bolt.
  
  Torque:
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }
INSTALL ENGINE SERVICE HOLE SUB COVER ASSEMBLY
1. Install the engine service hole sub cover with the 5 bolts.
  
  Torque:
  
  13 N*m { 133 kgf*cm, 10 ft.*lbf }
INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
1. Connect the front seat inner belt assembly connector and install the front seat assembly.
2. Align the front seat assembly adjuster pin with the holes in the body.
3. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
4. Temporarily tighten the 2 bolts on the front side of the front seat assembly.
5. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
6. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.
7. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
8. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
9. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
10. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
1. Connect the front seat inner belt assembly connector and install the front seat assembly.
2. Align the front seat assembly adjuster pin with the holes in the body.
3. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
4. Temporarily tighten the 2 bolts on the front side of the front seat assembly.
5. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
6. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.
7. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
8. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
9. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
10. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side Click here.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

5.4 N*m { 55 kgf*cm, 48 in.*lbf }
PERFORM INITIALIZATION
1. Some system need initialization when reconnecting the battery cable. Click here