REAR SEAT OUTER BELT ASSEMBLY(for 5 Door) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing Click here.

Tech Tips


  • Use the same procedure for the RH and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    1. A0046YZC03
      *1 Retractor
      *a Unlock
      *b Lock
      *c 45°

      Check the angle of inclination required to lock the retractor.


      1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

        Note

        Do not disassemble the retractor.

        If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

    2. A004A9VE01

      Engage the 2 hooks and temporarily install the rear seat 3 point type outer belt assembly with the 2 bolts.

    3. Tighten bolt A and then bolt B.

      Torque:
      for bolt A
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      for bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Connect the floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Check that the ELR locks.

      Note


      • The check should be performed with the rear seat 3 point type outer belt assembly installed.

      • Do not allow the anchor part of the rear seat 3 point type outer belt assembly and the protruding parts of the floor panel to overlap.


      1. With the belt installed, check that the belt locks when it is pulled out quickly.

        If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.

    7. A004AVTC01
      *a Locking Button

      Connect the pretensioner connector.

    8. Lock the locking button.

      Note

      Securely lock the locking button.

    9. Remove the bolt and floor anchor.

  2. INSTALL ROOF SIDE INNER GARNISH

    Click here

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

    Click here

  4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

    Click here

  5. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

    Click here

  6. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    1. Connect the rear door opening trim weatherstrip.

  7. INSTALL REAR DOOR SCUFF PLATE

    Click here

  8. INSTALL REAR FLOOR FINISH PLATE

    Click here

  9. INSTALL JACK HANDLE (for RH Side)

  10. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (for LH Side)

    Click here

  11. INSTALL SPARE WHEEL COVER (w/ Cover)

    Click here

  12. INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

    Click here

  13. INSTALL REAR SEAT ASSEMBLY (for RH Side)

    Click here

  14. INSTALL REAR SEAT ASSEMBLY (for LH Side)

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  16. INSPECT SRS WARNING LIGHT

    Click here