REAR DOOR WINDOW FRAME MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR DOOR REAR WINDOW FRAME LH

    Click here

  2. INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

    Click here

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  4. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH


    1. Install the rear door upper window frame moulding LH with 2 new clips.

  5. INSTALL REAR DOOR GLASS RUN LH

    Click here

  6. INSTALL REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY LH

    Click here

  7. INSTALL REAR DOOR OUTSIDE MOULDING INSERT LH


    1. Using an air riveter or hand riveter with a nose piece, install the rear door outside moulding insert LH with 2 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note


      • B004W74C11
        *a Riveter
        *b Mandrel
        *c Incorrect

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • B004UFSC10
        *a Riveter
        *b Incorrect

        Confirm that the rivets are seated properly against the moulding.

      • Do not tilt the riveter when installing the rivet to the moulding.

      • Do not leave any space between the rivet head and moulding.

      • B004VR9C10
        *a Riveter
        *b Incorrect

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

      B004VKQ

  8. INSTALL REAR DOOR WINDOW FRAME MOULDING LH(REAR PILLAR SIDE)

    Tech Tips

    When installing the rear door window frame moulding LH (rear pillar side), heat the vehicle body and rear door window frame moulding LH (rear pillar side) using a heat light.

    Standard
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Rear Door Window Frame Moulding LH (Rear Pillar Side) 20 to 30°C (68 to 86°F)

    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. B004YQ1C01
      *a Double-sided Tape
      B004RMI Install in this Direction

      Using a heat light, heat the vehicle body and a new rear door window frame moulding LH (rear pillar side).

    3. Remove the protective tape.

  9. INSTALL REAR DOOR FRONT GLASS RUN LH


    1. B004UMM

      Install the rear door front glass run LH.

  10. INSTALL REAR DOOR WINDOW FRAME MOULDING LH(CENTER PILLAR SIDE)


    1. B004XO4C01
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)

      Attach the guide and clip to install the rear door window frame moulding LH (center pillar side) as shown in the illustration.

    2. Install the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Remove the protective tape.

  11. INSTALL REAR DOOR NO. 3 GLASS RUN LH


    1. B004WYI

      Install the rear door No. 3 glass run LH.

  12. INSTALL REAR DOOR BELT MOULDING SUB-ASSEMBLY LH


    1. Using an air riveter or hand riveter with a nose piece, install the rear door belt moulding sub-assembly LH with 5 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note


      • B004W74C11
        *a Riveter
        *b Mandrel
        *c Incorrect

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • B004UFSC10
        *a Riveter
        *b Incorrect

        Confirm that the rivets are seated properly against the moulding.

      • Do not tilt the riveter when installing the rivet to the moulding.

      • Do not leave any space between the rivet head and moulding.

      • B004VR9C10
        *a Riveter
        *b Incorrect

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

      B004VWW

  13. INSTALL REAR DOOR BELT MOULDING LH

    Click here

  14. INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH

    Click here

  15. INSTALL REAR DOOR FRONT BELT MOULDING END COVER LH

    Click here

  16. INSTALL REAR DOOR REAR BELT MOULDING END COVER LH

    Click here

  17. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  18. INSTALL REAR MULTIPLEX NETWORK DOOR ECU LH

    Click here

  19. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  20. INSTALL REAR SIDE WINDOW COVER LH (w/ Rear Door Sunshade)

    Click here

  21. INSTALL REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

  22. INSTALL CURTAIN RAIL SIDE COVER LH (w/ Rear Door Sunshade)

    Click here

  23. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  24. INSTALL REAR DOOR NO. 2 FRAME GARNISH LH

    Click here

  25. INSTALL REAR DOOR TRIM COVER LH

    Click here

  26. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  27. INSTALL REAR DOOR NO. 2 ARMREST COVER LH

    Click here

  28. INSTALL REAR DOOR ARMREST COVER LH

    Click here

  29. INSTALL REAR DOOR TRIM UPPER COVER LH

    Click here

  30. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  31. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  32. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  33. CHECK POWER WINDOW CONTROL SYSTEM

    Click here

  34. INITIALIZE REAR DOOR SUNSHADE ASSEMBLY (w/ Rear Door Sunshade)

    Click here

  35. CHECK REAR DOOR SUNSHADE SYSTEM (w/ Rear Door Sunshade)

    Click here