FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type: Click here

for Mono Camera type: Click here

Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


    w/ Occupant Classification System:

  • Front seat assembly RH (Removal and installation)

 Zero point calibration (Occupant classification system)

  • Occupant classification system

  • Passenger airbag ON/OFF indicator

  • Airbag system (Front passenger side)

  • Seat belt warning system (Front passenger)

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B004U54

    Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT BELT HOLE COVER LH

    Click here

  3. REMOVE SEAT BELT ANCHOR COVER CAP LH

    Click here

  4. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (SEAT ANCHOR)


    1. B004STDC01
      B004RMI Remove in this Direction

      Remove the bolt.

    2. Detach the hook and remove the seat anchor of the front seat outer belt assembly LH from the hole of the front seat cushion shield LH.

  5. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  8. REMOVE CENTER LOWER PILLAR GARNISH LH

    Click here

  9. REMOVE CENTER UPPER PILLAR GARNISH LH

    Click here

  10. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    Tech Tips

    Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.


    1. B004TCH

      Remove the screw and rib.

    2. B004TY5

      Detach the guide and remove the front shoulder belt anchor plate sub-assembly LH.

  11. REMOVE FRONT SEAT SHOULDER BELT GUIDE


    1. B004VSI

      Remove the 2 screws.

    2. Detach the guide and remove the front seat shoulder belt guide.

  12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B004X9X

      Remove the nut and shoulder anchor of the front seat outer belt assembly LH.

    2. B004T9M

      Detach the 3 clamps and fold the floor carpet as shown in the illustration so that the clip of the No. 2 floor heater air duct LH can be removed.

    3. Remove the clip.

    4. B004WMM

      Move the No. 2 floor heater air duct LH as shown in the illustration so that the bolts of the retractor can be removed.

      Note

      Move the No. 2 floor heater air duct LH gently and do not damage it.

    5. w/o Pre-collision Seat Belt:


      1. B004WJ9C01
        *a Locking Button
        B004VGX Protective Tape
        B004SZX Pretensioner Connector
        B004UK4 Tension Reducer Connector

        Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Disconnect the tension reducer connector.

      3. B004VNP

        Remove the 2 bolts.

      4. Detach the guide and remove the front seat outer belt assembly LH.

    6. w/ Pre-collision Seat Belt:


      1. B004TCYC01
        *a Locking Button
        B004VGX Protective Tape
        B004SZX Pretensioner Connector
        B004UK4 Motor Connector

        Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Disconnect the motor connector.

      3. B004V5DN01

        Loosen the bolt A and remove the bolt B.

      4. Detach the guide and remove the front seat outer belt assembly LH.

  13. REMOVE FRONT SEAT BELT RETRACTOR COVER LH


    1. B004S6PC01
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Pull in the removal direction (1) shown in the illustration to detach the claw.

    2. Slide in the removal direction (2) shown in the illustration to detach the guide and remove the front seat belt retractor cover LH.

  14. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B004UZP

      Remove the 2 bolts.

    2. Detach the guide and remove the front shoulder belt anchor adjuster assembly.