FRONT SEAT INNER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat inner belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Stereo Camera type: Click here for Mono Camera type: Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Stereo camera type)
		Pre-collision system (for Mono camera type)
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
w/ Occupant Classification System: Front seat assembly RH (Removal and installation)	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

PRECAUTION
CAUTION:
- Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
  
  Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- There is risk of injury.
Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
REMOVE FRONT SEAT ASSEMBLY LH

Click here
REMOVE FRONT SEAT ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.

REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

Disconnect the 2 connectors.

*A	for 2WD	*B	for AWD
*C	w/o Easy Access Buckle	*D	w/ Easy Access Buckle
	Remove in this Direction		Protective Tape

Detach the wire harness clamp.
Using a screwdriver, detach the claw and remove the connector.

Tech Tips

Tape the screwdriver tip before use.
w/ Easy Access Buckle:
1. Remove the 2 nuts.
2. Remove in this Direction
  
  Pass the buckle of the front seat inner belt assembly LH through the hole of the separate type front seat cushion cover LH and remove the front seat inner belt assembly LH.
w/o Easy Access Buckle:
1. Remove the nut and front seat inner belt assembly LH.
Remove the front seat belt anchor plate.

REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

w/ Occupant Classification System:
1. Disconnect the 2 connectors.
  
  *A w/ Easy Access Buckle *B w/o Easy Access Buckle
2. Detach the wire harness clamp.

w/o Occupant Classification System:

Disconnect the connector.

*A	w/ Easy Access Buckle	*B	w/o Easy Access Buckle
	Remove in this Direction		Protective Tape

Detach the wire harness clamp.
Using a screwdriver, detach the claw and remove the connector.

Tech Tips

Tape the screwdriver tip before use.

w/ Easy Access Buckle:
1. Remove the 2 nuts.
2. Remove in this Direction
  
  Pass the buckle of the front seat inner belt assembly RH through the hole of the separate type front seat cushion cover RH and remove the front seat inner belt assembly RH.
w/o Easy Access Buckle:
1. Remove the nut and front seat inner belt assembly RH.
Remove the front seat belt anchor plate.