Click here

SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) Front Passenger Side Seat Belt Warning Light does not Operate

Click here
Click here
DTC Code DTC Name
  Front Passenger Side Seat Belt Warning Light does not Operate
Click here

DESCRIPTION

When the power switch is turned on (IG), the occupant detection ECU sends signals to the airbag ECU assembly to indicate the state of the front seat inner belt assembly RH and also whether the front passenger seat is occupied. The airbag ECU assembly sends those signals to the combination meter assembly via CAN communication. The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with these signals.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click here

Tip:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click here

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)


    1. Clear the DTCs.


      1. Body Electrical > Occupant Detection > Clear DTCs


    2. Check for DTCs.


      1. Body Electrical > Occupant Detection > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTCs are output B

  2. Click here

    CHECK DTC OUTPUT (AIRBAG SYSTEM)


    1. Clear the DTCs.


      1. Body Electrical > SRS Airbag > Clear DTCs


    2. Check for DTCs.


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTCs are output B

  3. Click here

    READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Occupant Detection / Data List.

    5. Read the Data List according to the display on the GTS.


      1. Body Electrical > Occupant Detection > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Passenger Buckle SW Front passenger buckle switch Unset, Set or NG

        Unset: Seat belt not fastened

        Set: Seat belt fastened

        NG: Data is not determined

        		 -



      1. Body Electrical > Occupant Detection > Data List
        Tester Display
        Passenger Buckle SW




      Result
      Result Proceed to
      Unset or Set is displayed on the GTS according to the front passenger seat belt condition A
      Unset or Set is not displayed correctly on the GTS according to the front passenger seat belt condition B
      NG is displayed on the GTS C

  4. Click here

    READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / SRS Airbag / Data List.

    5. Read the Data List according to the display on the GTS.


      1. Body Electrical > SRS Airbag > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Right side Buckle SW RH buckle switch Unset, Set or NG

        Unset: Seat belt not fastened

        Set: Seat belt fastened

        NG: Data is not determined

        		 -



      1. Body Electrical > SRS Airbag > Data List
        Tester Display
        Right side Buckle SW




      Result
      Result Proceed to
      Unset or Set is displayed on the GTS according to the front passenger seat belt condition A

      • Unset or Set is not displayed correctly on the GTS according to the front passenger seat belt condition

      • NG is displayed on the GTS

      		 B