Click here

OCCUPANT DETECTION SENSOR(for Power Seat) INSTALLATION

Click here
Click here

CAUTION / NOTICE / HINT

CAUTION:
B004VVX

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    INSTALL REAR CENTER SEAT CUSHION PAD


    1. Install the rear center seat cushion pad to the center seat cushion frame sub-assembly.

    2. B004SQK

      Attach the claw and connect the connector of the occupant detection sensor.

  2. Click here

    INSTALL REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY

    Click here

  3. Click here

    INSTALL REAR SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

  4. Click here

    INSTALL REAR SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

  5. Click here

    INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004W9UC01
      B004RMI Install in this Direction

      Attach the hooks and install the seat cushion main stretcher cushion assembly.

    2. Clean the felt installation surface.


      1. When reusing the rear seat cushion pad LH, remove the felt remaining on the installation surface.

    3. B004SZ4C01
      *a 2nd Step of The Bladder

      Install 2 new pieces of felt in the positions shown in the illustration.

      Note:

      • The L-shaped joint must not stick out.

      • Do not cover the 2nd step of the bladder.

    4. B004R9WC01
      *a Orange Tube Color
      *b Green Tube Color
      *c Clear Tube Color

      Place the tube as shown in the illustration and using a tacker, install the strap with new tack pins.

  6. Click here

    INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tip:

    Use the same procedure described for the LH side.

  7. Click here

    INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004WM7C01
      B004RMI Install in this Direction

      Attach the hooks and install the seat cushion main stretcher cushion assembly.

    2. Clean the felt installation surface.


      1. When reusing the rear seat cushion pad LH, remove the felt remaining on the installation surface.

    3. B004T3KC01
      *a 2nd Step of The Bladder

      Install 2 new pieces of felt in the positions shown in the illustration.

      Note:

      • The L-shaped joint must not stick out.

      • Do not cover the 2nd step of the bladder.

    4. B004VU3C01
      *a Yellow Tube Color
      *b Blue Tube Color
      *c Clear Tube Color

      Place the tube as shown in the illustration and using a tacker, install the strap with new tack pins.

  8. Click here

    INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tip:

    Use the same procedure described for the LH side.

  9. Click here

    INSTALL REAR SEAT CUSHION PAD (w/ Refresh Seat)


    1. Clean double-sided tape installation surface.


      1. When reusing the rear seat cushion pad, remove the double-sided tape remaining on the installation surface.

    2. Remove the peeling paper from the face of the rear seat cushion pad.

      Tip:

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the rear seat cushion pad in the position shown in the illustration.

    4. B004XFMC01
      *a Hog Ring Pliers - -
      B004VH3 Double-sided Tape - -

      Pull out the strap from the hole of the rear seat cushion pad.

    5. Using hog ring pliers, install the rear seat cushion pad with 4 new hog rings.

  10. Click here

    INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH

    Tip:

    Refer to the precautions on wrinkles to avoid creating any on the separate type rear seatback cover LH when installing the seat cover.

    Click here


    1. Install the separate type rear seat cushion cover LH to the rear seat cushion pad LH.

    2. B004SEVC01
      *a Hog Ring Pliers - -

      Using hog ring pliers, securely install 14 new hog rings in the order shown in the illustration, and then install the separate type rear seat cushion cover LH to the rear seat cushion pad LH.

      Note:

      • Do not dirty or damage the separate type rear seat cushion cover LH.

      • Be sure to securely tighten the hog rings as shown in the illustration while preventing wrinkles from forming on the center of the rear seat cushion pad LH and fabric.

  11. Click here

    INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tip:

    Use the same procedure described for the LH side.

  12. Click here

    INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH

    Click here

  13. Click here

    INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Click here

  14. Click here

    INSTALL SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  15. Click here

    INSTALL SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Click here

  16. Click here

    INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  17. Click here

    INSTALL REAR SEAT CUSHION ASSEMBLY LH

    Click here

  18. Click here

    INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  19. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  20. Click here

    INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  21. Click here

    CHECK SRS WARNING LIGHT

    Click here

  22. Click here

    INSPECT REAR SEAT ASSEMBLY

    Click here

  23. Click here

    INSPECT SEAT HEATER SYSTEM

    Click here

  24. Click here

    INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here

  25. Click here

    INSPECT SEAT VIBRATION SYSTEM (w/ Refresh Seat)

    Click here

  26. Click here

    INSPECT SEAT BELT WARNING SYSTEM


    1. w/ Occupant Classification System:

      Click here

    2. w/o Occupant Classification System:

      Click here