Click here

OCCUPANT DETECTION SENSOR(for Power Seat) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the occupant detection sensor removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Mono Camera type:Click here

for Stereo Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic View Monitor System

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
CAUTION:
B004VVX

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:
    B004UM0

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY LH

    Click here

  4. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  5. Click here

    REMOVE REAR CENTER SEAT CUSHION ASSEMBLY

    Click here

  6. Click here

    REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. Click here

    REMOVE SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  8. Click here

    REMOVE SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Click here

  9. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH

    Click here

  10. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Tip:

    Use the same procedure described for the LH side.

  11. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. B004WP1

      Remove the 8 hog rings and pull out the strap from the hole of the rear seat cushion pad LH.

    2. Remove the 6 hog rings and separate type rear seat cushion cover LH.

  12. Click here

    REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tip:

    Use the same procedure described for the LH side.

  13. Click here

    REMOVE REAR SEAT CUSHION PAD (w/ Refresh Seat)


    1. B004VZUC01
      B004VH3 Double-sided Tape - -

      Remove the 4 hog rings and pull out the strap from the hole of the rear seat cushion pad.

    2. Remove the double-sided tape and rear seat cushion pad.

  14. Click here

    REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004XFEC01

      Cut the tack pin and fold back the strap.

    2. B004RID

      Remove the 2 pieces of felt.

    3. B004XNNC01
      B004RMI Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  15. Click here

    REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tip:

    Use the same procedure described for the LH side.

  16. Click here

    REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004UH7

      Cut the tack pin and fold back the strap.

    2. B004THU

      Remove the 2 pieces of felt.

    3. B004RFFC02
      B004RMI Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  17. Click here

    REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tip:

    Use the same procedure described for the LH side.

  18. Click here

    REMOVE REAR SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

  19. Click here

    REMOVE REAR SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

  20. Click here

    REMOVE REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY

    Click here

  21. Click here

    REMOVE REAR CENTER SEAT CUSHION PAD


    1. B004W2JC01
      B004VGX Double-sided Tape

      Using a thin-bladed screwdriver wrapped with protective tape, detach the claw and disconnect the connector of the occupant detection sensor.

    2. Remove the rear center seat cushion pad from the center seat cushion frame sub-assembly.