REAR POWER SEAT CONTROL SYSTEM, Diagnostic DTC:B265E

DTC Code DTC Name
B265E Headrest Front/Rear Sensor Malfunction

DESCRIPTION

When the position control ECU assembly does not receive a sensor signal despite forward or rearward movement of the seat head rest by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B265E Headrest Front/Rear Sensor Malfunction The forward and rearward lock detection position of the sensor is the same.

  • Position control ECU assembly LH

  • Position control ECU assembly RH

  • Rear No. 2 seat headrest adjuster sub-assembly (headrest front/back motor)

  • Rear No. 1 seat headrest adjuster sub-assembly (headrest front/back motor)

  • Harness or connector

WIRING DIAGRAM


  1. for Rear Seat RH:

    Figure 1. for LHD:

    B004TBVE04

    Figure 2. for RHD:

    B004TBVE05

  2. for Rear Seat LH:

    Figure 3. for LHD:

    B004TBVE06

    Figure 4. for RHD:

    B004TBVE07

CAUTION / NOTICE / HINT

Note

Initializing the position control ECU assembly will clear the seat position memory.

Tech Tips


  • Make sure to initialize the position control ECU assembly after replacing the seat assembly or any related parts (including removal and installation).

  • Before initializing the seat ECU, make sure that the D/C CUT fuse is normal.

  • When any of the following conditions are met, the seat position Information in the position control ECU assembly will be cleared.


    • The power switch is turned off with any of the seat switches being operated and the D/C CUT fuse removed.

    • The power switch is turned off within 1 second of any of the seat switches being operated with the D/C CUT fuse removed.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Rear Right Seat > Clear DTCs
      Body Electrical > Rear Left Seat > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Rear Right Seat > Trouble Codes
      Body Electrical > Rear Left Seat > Trouble Codes
      OK
      DTC B265E is not output.
      Result
      Result Proceed to
      DTC B265E is not output A
      DTC B265E output from "Rear Right Seat" B
      DTC B265E output from "Rear Left Seat" C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    PERFORM ACTIVE TEST USING GTS (HEADREST OPERATION) Click here

    B

  3. PERFORM ACTIVE TEST USING GTS (HEADREST FRONT/REAR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Rear Right Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Rear Right Seat > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Headrest Front/Rear Headrest Front/Rear operation OFF/Front/Rear -

      Body Electrical > Rear Right Seat > Active Test
      Tester Display
      Headrest Front/Rear
      OK
      Motor operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR) Click here

    OK

  4. CHECK POSITION CONTROL ECU ASSEMBLY RH (HEADRST MOTOR CIRCUIT)


    1. Disconnect the rear seat headrest adjuster sub-assembly (headrest front/rear motor) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      R3-3 - R3-4 Headrest switch on 4.8 to 5.1 V
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    B

    REPLACE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    C

  5. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR))


    1. Disconnect the R7 position control ECU assembly RH connector.

    2. Disconnect the R3 rear No. 2 seat headrest adjuster sub-assembly*1 or rear No. 1 seat headrest adjuster sub-assembly*2 (headrest front/rear motor) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R7-25 (SSHD) - R3-4 Always Below 1 Ω
      R7-25 (SSHD) or R3-4 - Other terminals and body ground Always 10 kΩ or higher
      R7-7 (SGND) - R3-3 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POSITION CONTROL ECU ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. INSPECT REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR)


    1. for LHD:


      1. Remove the rear No. 2 seat headrest adjuster sub-assembly.

        Click here

      2. Inspect the rear No. 2 seat headrest adjuster sub-assembly.

        Click here

    2. for RHD:


      1. Remove the rear No. 1 seat headrest adjuster sub-assembly.

        Click here

      2. Inspect the rear No. 1 seat headrest adjuster sub-assembly.

        Click here

      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    C

    REPLACE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    A

  7. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST UP/DOWN MOTOR))


    1. Disconnect the R4 and R5 position control ECU assembly RH connectors.

    2. Disconnect the R3 rear No. 2 seat headrest adjuster sub-assembly*1 or rear No. 1 seat headrest adjuster sub-assembly*2 connector


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R5-7 (HD+) - R3-2 Always Below 1 Ω
      R5-7 (HD+) or R3-2 - Other terminals and body ground Always 10 kΩ or higher
      R4-3 (HD-) - R3-1 Always Below 1 Ω
      R4-3 (HD-) or R3-1 - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POSITION CONTROL ECU ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. PERFORM ACTIVE TEST USING GTS (HEADREST OPERATION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Rear Left Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Rear Left Seat > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Headrest Front/Rear Headrest front/rear operation OFF/Down/Up -

      Body Electrical > Rear Left Seat > Active Test
      Tester Display
      Headrest Front/Rear
      OK
      Motor operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR) Click here

    OK

  9. CHECK POSITION CONTROL ECU ASSEMBLY LH (HEADRST MOTOR CIRCUIT)


    1. Disconnect the rear seat headrest adjuster sub-assembly (headrest front/rear motor) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      R37-3 - R37-4 Headrest switch on 4.8 to 5.1 V
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    B

    REPLACE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    C

  10. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR))


    1. Disconnect the R41 position control ECU assembly LH connector.

    2. Disconnect the R37 rear No. 1 seat headrest adjuster sub-assembly*1 or rear No. 2 seat headrest adjuster sub-assembly*2 (headrest up/down motor) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R41-25 (SSHD) - R37-4 Always Below 1 Ω
      R41-25 (SSHD) or R37-4 - Other terminals and body ground Always 10 kΩ or higher
      R41-7 (SGND) - R37-3 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POSITION CONTROL ECU ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  11. INSPECT REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR)


    1. for LHD:


      1. Remove the rear No. 1 seat headrest adjuster sub-assembly.

        Click here

      2. Inspect the rear No. 1 seat headrest adjuster sub-assembly.

        Click here

    2. for RHD:


      1. Remove the rear No. 2 seat headrest adjuster sub-assembly.

        Click here

      2. Inspect the rear No. 2 seat headrest adjuster sub-assembly.

        Click here

      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    C

    REPLACE REAR NO. 2 SEAT HEADREST ADJUSTER SUB-ASSEMBLY Click here

    A

  12. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - REAR SEAT HEADREST ADJUSTER SUB-ASSEMBLY (HEADREST FRONT/REAR MOTOR))


    1. Disconnect the R38 and R39 position control ECU assembly RH connectors.

    2. Disconnect the R37 rear No. 1 seat headrest adjuster sub-assembly*1 or rear No. 2 seat headrest adjuster sub-assembly*2 connector


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R39-7 (HD+) - R37-2 Always Below 1 Ω
      R39-7 (HD+) or R37-2 - Other terminals and body ground Always 10 kΩ or higher
      R38-3 (HD-) - R37-1 Always Below 1 Ω
      R38-3 (HD-) or R37-1 - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POSITION CONTROL ECU ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR