PRE-COLLISION SYSTEM(for Stereo Camera Type), Diagnostic DTC:C142571

DTC Code DTC Name
C142571 Stop Light Relay Actuator Stuck

DESCRIPTION

The stop light switch assembly and skid control ECU assembly outputs stop light signals to the No. 3 semiconductor power integration ECU. When the skid control ECU assembly detects a malfunction relating to the stop light circuit, the driving support ECU is notified via CAN communication, and C1A4B is output.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C142571 Stop Light Relay Actuator Stuck

Diagnosis Condition:


  • +BI1 and +BI2 terminal voltage is 8.9 V or higher

Malfunction status:

Either of the following occurs


  • When STPO is ON and STP is OFF, STP2 is OFF continuously for 0.3 seconds or more

  • When STPO is OFF and STP and STP2 input signal statuses differ continuously for 0.3 seconds or more

  • Power integration system

  • Skid control ECU assembly

  • Harness or connector

  • Rear combination light lens and body LH

  • Rear combination light lens and body RH

  • Rear combination light LED

  • Rear light lens and body LH

  • Rear light lens and body RH

  • Rear light LED

  • Center stop light assembly

  • Center stop light wire

  • No. 3 semiconductor power integration ECU

  • Shift control ECU

  • Certification ECU (smart key ECU assembly)

  • Hybrid vehicle control ECU assembly

  • Vehicle approaching speaker controller

  • Stop light switch assembly

 Driving support ECU assembly (Pre-Collision System)
DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition +BI1 and +BI2 terminal voltage is 8.9 V or higher ○ ○
Malfunction Status When STPO is ON and STP is OFF, STP2 is OFF continuously ○ -
When STPO is OFF and STP and STP2 input signal statuses differ continuously - ○
Detection Time 0.3 seconds or more 0.3 seconds or more
Number of Trips 1 trip 1 trip

Tech Tips

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

B004V6FE03
*1 Shift Control ECU
*2 Certification ECU (Smart Key ECU Assembly)
*3 Hybrid Vehicle Control ECU Assembly
B004WDWE01
B004T4ME01

CAUTION / NOTICE / HINT

Note


  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • The vehicle is equipped with a sub-battery. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

    for L310: Click here

    for L310F: Click here

PROCEDURE


  1. CHECK FOR DTCs (POWER INTEGRATION SYSTEM)


    1. Check for DTCs.

      Click here


      Body Electrical > Power Integration No.3 > Trouble Codes

      Tech Tips

      If there is a malfunction in the No. 3 semiconductor integration ECU, integration relay system DTCs may also have been detected. Check the integration relay system first.

      Result
      Result Proceed to
      Power integration system DTCs are not output A
      Power integration system DTCs are output B

    B

    GO TO POWER INTEGRATION SYSTEM Click here

    A

  2. READ VALUE USING GTS (STOP LIGHT INPUT SIGNAL, STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Using the GTS, check the Data List "Stop Light Input Signal", "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Input Signal Stop light switch assembly input condition ON or OFF

      OFF: Brake pedal released

      ON: Brake pedal depressed

      		 -
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Input Signal
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Input Signal Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON ON Connect
      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Input Signal Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON ON Connect A
      ON OFF Connect B
      ON OFF Disconnect C
      OFF OFF Connect D

    B

    GO TO POWER INTEGRATION SYSTEM Click here

    C

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

    D

    CHECK TERMINAL VOLTAGE (STP TERMINAL) Click here

    A

  3. CHECK TERMINAL VOLTAGE (STP, STPO AND STP2 TERMINAL)


    1. Disconnect the A11 and A12 skid control ECU assembly connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A12-16 (STP) - Body ground Brake pedal depressed 8 to 14 V
      Brake pedal released Below 1.5 V
      A12-4 (STPO) - Body ground Power switch off 8 to 14 V
      A11-14 (STP2) - Body ground Brake pedal depressed 8 to 14 V
      Brake pedal released Below 1.5 V

    3. Connect the A11 and A12 skid control ECU assembly connectors.

      Result
      Result Proceed to
      All terminal voltage is normal A
      Only STP terminal voltage abnormal B
      Only STPO terminal voltage abnormal C
      Only STP2 terminal voltage abnormal D
      STPO terminal and STP2 terminal voltage abnormal E

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU) Click here

    D

    CHECK TERMINAL VOLTAGE (STP2 TERMINAL) Click here

    E

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU) Click here

    A

  4. PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)


    1. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    2. Perform "Active Test" according to the display on the GTS.

      Click here


      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay No. 3 semiconductor power integration ECU ECU (Stop light output) ON/OFF Stop lights come on

      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display
      Stop Light Relay
      OK
      Stop light turns ON/OFF in response to the GTS operation
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT SKID CONTROL ECU ASSEMBLY Click here

    OK

  5. CHECK FOR DTC (PRE-COLLISION SYSTEM)


    1. Clear the DTCs.

      Click here


      Body Electrical > Pre-Collision System > Clear DTCs

    2. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    3. Perform "Active Test" according to the display on the GTS.


      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay No. 3 semiconductor power integration ECU ECU (Stop light output) ON/OFF Stop lights come on

      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display
      Stop Light Relay

    4. Check for DTCs.

      Click here


      Body Electrical > Pre-Collision System > Trouble Codes
      Result
      Result Proceed to
      DTC C1A4B is not output A
      DTC C1A4B is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE SKID CONTROL ECU ASSEMBLY Click here

  6. INSPECT SKID CONTROL ECU ASSEMBLY


    1. Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

    2. Perform "Active Test" according to the display on the GTS.


      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay No. 3 semiconductor power integration ECU ECU (Stop light output) ON / OFF Stop lights come on

      Chassis > ABS/VSC/TRAC > Active Test
      Tester Display
      Stop Light Relay
    3. B004W09C08
      *a

      Component with harness connected

      (No. 3 Semiconductor Power Integration ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-14 (ACC) - Body ground Active test is ON Below 1.5 V
      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

    REPLACE SKID CONTROL ECU ASSEMBLY Click here

  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU)


    1. Disconnect the A12 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A12-4 (STPO) - L111-14 (ACC) Always Below 1 Ω

    4. Connect the L111 No. 3 semiconductor power integration ECU connector.

    5. Connect the A12 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK TERMINAL VOLTAGE (STP2 TERMINAL)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    3. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A11 skid control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L111-1 (OUT) - A11-14 (STP2) Always Below 1 Ω

    4. Connect the A11 skid control ECU assembly connector.

    5. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    4. Connect the L111 No. 3 semiconductor power integration ECU connector.

    5. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

  11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    5. Connect the L82 rear combination light assembly LH connector.

    6. Connect the L111 No. 3 semiconductor power integration ECU connector.

    7. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH) Click here

    OK

  12. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR COMBINATION LIGHT LED)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the rear combination light LED (rear combination light assembly LH side) connector.

      Tech Tips

      Click here

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    5. Connect the the rear combination light LED (rear combination light assembly LH side) connector.

    6. Connect the L111 No. 3 semiconductor power integration ECU connector.

    7. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR COMBINATION LIGHT LED Click here

    NG

    REPLACE REAR COMBINATION LIGHT LENS AND BODY LH Click here

  13. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU)


    1. Disconnect the A12 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A12-4 (STPO) or L111-14 (ACC) - Body ground Always 10 kΩ or higher

    4. Connect the L111 No. 3 semiconductor power integration ECU connector.

    5. Connect the A12 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    6. Connect the L81 rear combination light assembly RH connector.

    7. Connect the L82 rear combination light assembly LH connector.

    8. Connect the L111 No. 3 semiconductor power integration ECU connector.

    9. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LENS AND BODY LH) Click here

    OK

  15. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR COMBINATION LIGHT LED)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the rear combination light LED (rear combination light assembly RH side) connector.

      Tech Tips

      Click here

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    6. Connect the rear combination light LED (rear combination light assembly RH side) connector.

    7. Connect the L82 rear combination light assembly LH connector.

    8. Connect the L111 No. 3 semiconductor power integration ECU connector.

    9. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR COMBINATION LIGHT LED Click here

    NG

    REPLACE REAR COMBINATION LIGHT LENS AND BODY RH Click here

  16. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    3. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

    A

  17. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the rear combination light LED (rear combination light lens and body LH side) connector.

      Tech Tips

      Click here

    2. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    3. Connect the rear combination light LED (rear combination light lens and body LH side) connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE REAR COMBINATION LIGHT LED Click here

    B

    REPLACE REAR COMBINATION LIGHT LENS AND BODY LH Click here

  18. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LENS AND BODY LH)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    7. Connect the L86 rear light lens and body LH connector.

    8. Connect the L81 rear combination light assembly RH connector.

    9. Connect the L82 rear combination light assembly LH connector.

    10. Connect the L111 No. 3 semiconductor power integration ECU connector.

    11. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LENS AND BODY RH) Click here

    OK

  19. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LED)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the rear light LED (rear light lens and body LH side) connector.

      Tech Tips

      Click here

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    7. Connect the rear light LED (rear light lens and body LH side) connector.

    8. Connect the L81 rear combination light assembly RH connector.

    9. Connect the L82 rear combination light assembly LH connector.

    10. Connect the L111 No. 3 semiconductor power integration ECU connector.

    11. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR LIGHT LED Click here

    NG

    REPLACE REAR LIGHT LENS AND BODY LH Click here

  20. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    4. Connect the L81 rear combination light assembly RH connector.

    5. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

    A

  21. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the rear combination light LED (rear combination light lens and body RH side) connector.

      Tech Tips

      Click here

    3. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    4. Connect the rear combination light LED (rear combination light lens and body RH side) connector.

    5. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE REAR COMBINATION LIGHT LED Click here

    B

    REPLACE REAR COMBINATION LIGHT LENS AND BODY RH Click here

  22. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LENS AND BODY RH)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Disconnect the L90 rear light lens and body RH connector.

    7. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    8. Connect the L90 rear light lens and body RH connector.

    9. Connect the L86 rear light lens and body LH connector.

    10. Connect the L81 rear combination light assembly RH connector.

    11. Connect the L82 rear combination light assembly LH connector.

    12. Connect the L111 No. 3 semiconductor power integration ECU connector.

    13. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - CENTER STOP LIGHT ASSEMBLY) Click here

    OK

  23. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - REAR LIGHT LED)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Disconnect the rear light LED (rear light lens and body RH side) connector.

      Tech Tips

      Click here

    7. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    8. Connect the rear light LED (rear light lens and body RH side) connector.

    9. Connect the L86 rear light lens and body LH connector.

    10. Connect the L81 rear combination light assembly RH connector.

    11. Connect the L82 rear combination light assembly LH connector.

    12. Connect the L111 No. 3 semiconductor power integration ECU connector.

    13. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR LIGHT LED Click here

    NG

    REPLACE REAR LIGHT LENS AND BODY RH Click here

  24. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    5. Connect the L86 rear light lens and body LH connector.

    6. Connect the L81 rear combination light assembly RH connector.

    7. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

    A

  25. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the rear light LED (rear light lens and body LH side) connector.

      Tech Tips

      Click here

    4. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    5. Connect the rear light LED (rear light lens and body LH side) connector.

    6. Connect the L81 rear combination light assembly RH connector.

    7. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE REAR LIGHT LED Click here

    B

    REPLACE REAR LIGHT LENS AND BODY LH Click here

  26. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Disconnect the L90 rear light lens and body RH connector.

    7. Disconnect the A center stop light assembly connector.

    8. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    9. Connect the A center stop light assembly connector.

    10. Connect the L90 rear light lens and body RH connector.

    11. Connect the L86 rear light lens and body LH connector.

    12. Connect the L81 rear combination light assembly RH connector.

    13. Connect the L82 rear combination light assembly LH connector.

    14. Connect the L111 No. 3 semiconductor power integration ECU connector.

    15. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CENTER STOP LIGHT ASSEMBLY Click here

    NG

  27. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - CENTER STOP LIGHT WIRE)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Disconnect the L90 rear light lens and body RH connector.

    7. Disconnect the L71 center stop light wire connector.

    8. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    9. Connect the L71 center stop light wire connector.

    10. Connect the L90 rear light lens and body RH connector.

    11. Connect the L86 rear light lens and body LH connector.

    12. Connect the L81 rear combination light assembly RH connector.

    13. Connect the L82 rear combination light assembly LH connector.

    14. Connect the L111 No. 3 semiconductor power integration ECU connector.

    15. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CENTER STOP LIGHT WIRE Click here

    NG

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER) Click here

  28. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    6. Connect the L90 rear light lens and body RH connector.

    7. Connect the L86 rear light lens and body LH connector.

    8. Connect the L81 rear combination light assembly RH connector.

    9. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

    A

  29. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the rear light LED (rear light lens and body RH side) connector.

      Tech Tips

      Click here

    5. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    6. Connect the rear light LED (rear light lens and body RH side) connector.

    7. Connect the L86 rear light lens and body LH connector.

    8. Connect the L81 rear combination light assembly RH connector.

    9. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE REAR LIGHT LED Click here

    B

    REPLACE REAR LIGHT LENS AND BODY RH Click here

  30. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)


    1. Disconnect the A11 skid control ECU assembly connector.

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the L82 rear combination light assembly LH connector.

    4. Disconnect the L81 rear combination light assembly RH connector.

    5. Disconnect the L86 rear light lens and body LH connector.

    6. Disconnect the L90 rear light lens and body RH connector.

    7. Disconnect the L71 center stop light wire connector.

    8. Disconnect the G90 vehicle approaching speaker controller connector.

    9. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A11-14 (STP2) - Body ground Brake pedal released Below 1.5 V

    10. Connect the G90 vehicle approaching speaker controller connector.

    11. Connect the L71 center stop light wire connector.

    12. Connect the L90 rear light lens and body RH connector.

    13. Connect the L86 rear light lens and body LH connector.

    14. Connect the L81 rear combination light assembly RH connector.

    15. Connect the L82 rear combination light assembly LH connector.

    16. Connect the L111 No. 3 semiconductor power integration ECU connector.

    17. Connect the A11 skid control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  31. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed 8 to 14 V

    3. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

  32. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A12 skid control ECU assembly connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed 8 to 14 V

    4. Connect the A12 skid control ECU assembly connector.

    5. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SKID CONTROL ECU ASSEMBLY Click here

    NG

    CHECK TERMINAL VOLTAGE (STP TERMINAL) Click here

  33. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Disconnect the A center stop light assembly connector.

    6. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    7. Connect the A center stop light assembly connector.

    8. Connect the L90 rear light lens and body RH connector.

    9. Connect the L86 rear light lens and body LH connector.

    10. Connect the L81 rear combination light assembly RH connector.

    11. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE CENTER STOP LIGHT ASSEMBLY Click here

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

  34. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A12 skid control ECU assembly connector.

    3. Disconnect the A77 hybrid vehicle control ECU assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed 8 to 14 V

    5. Connect the A77 hybrid vehicle control ECU assembly connector.

    6. Connect the A12 skid control ECU assembly connector.

    7. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY Click here

    NG

    CHECK TERMINAL VOLTAGE (STP TERMINAL) Click here

  35. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Disconnect the L71 center stop light wire connector.

    6. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    7. Connect the L71 center stop light wire connector.

    8. Connect the L90 rear light lens and body RH connector.

    9. Connect the L86 rear light lens and body LH connector.

    10. Connect the L81 rear combination light assembly RH connector.

    11. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE CENTER STOP LIGHT WIRE Click here

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

  36. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A12 skid control ECU assembly connector.

    3. Disconnect the A77 hybrid vehicle control ECU assembly connector.

    4. Disconnect the L31 certification ECU (smart key ECU assembly) connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed 8 to 14 V

    6. Connect the L31 certification ECU (smart key ECU assembly) connector.

    7. Connect the A77 hybrid vehicle control ECU assembly connector.

    8. Connect the A12 skid control ECU assembly connector.

    9. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    CHECK TERMINAL VOLTAGE (STP TERMINAL) Click here

  37. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Disconnect the L71 center stop light wire connector.

    6. Disconnect the A11 skid control ECU assembly connector.

    7. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    8. Connect the A11 skid control ECU assembly connector.

    9. Connect the L71 center stop light wire connector.

    10. Connect the L90 rear light lens and body RH connector.

    11. Connect the L86 rear light lens and body LH connector.

    12. Connect the L81 rear combination light assembly RH connector.

    13. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE SKID CONTROL ECU ASSEMBLY Click here

    B

    READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE) Click here

  38. CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A12 skid control ECU assembly connector.

    3. Disconnect the A77 hybrid vehicle control ECU assembly connector.

    4. Disconnect the L31 certification ECU (smart key ECU assembly) connector.

    5. Disconnect the G82 shift control ECU connector.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed 8 to 14 V

    7. Connect the G82 shift control ECU connector.

    8. Connect the L31 certification ECU (smart key ECU assembly) connector.

    9. Connect the A77 hybrid vehicle control ECU assembly connector.

    10. Connect the A12 skid control ECU assembly connector.

    11. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SHIFT CONTROL ECU Click here

    NG

    CHECK HARNESS AND CONNECTOR (NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU - STOP LIGHT SWITCH ASSEMBLY) Click here

  39. READ VALUE USING GTS (STOP LIGHT OUTPUT SIGNAL AND STATUS OF STOP LIGHT FUSE)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Disconnect the L71 center stop light wire connector.

    6. Disconnect the A11 skid control ECU assembly connector.

    7. Disconnect the G90 vehicle approaching speaker controller connector.

    8. Using the GTS, check the Data List "Stop Light Output Signal" and "Status of Stop Light Fuse" with the brake pedal operated.

      Click here


      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Output Signal Stop light output condition ON or OFF

      OFF:

      Stop light is off

      ON:

      Stop light is on

      		 Stop lights blink during emergency brake signal control
      Status of Stop Light Fuse Stop light fuse condition Disconnect or Connect

      Disconnect: Fuse shut off

      Connect: Fuse not shut off

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display
      Stop Light Output Signal
      Status of Stop Light Fuse
      Standard
      Brake pedal operation Data List Display Condition
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect

    9. Connect the G90 vehicle approaching speaker controller connector.

    10. Connect the A11 skid control ECU assembly connector.

    11. Connect the L71 center stop light wire connector.

    12. Connect the L90 rear light lens and body RH connector.

    13. Connect the L86 rear light lens and body LH connector.

    14. Connect the L81 rear combination light assembly RH connector.

    15. Connect the L82 rear combination light assembly LH connector.

      Result
      Brake pedal operation Data List Display Condition Result
      Stop Light Output Signal Status of Stop Light Fuse
      Brake pedal depressed ON Connect A
      OFF Disconnect B

    A

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER Click here

    B

  40. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU)


    1. Disconnect the L82 rear combination light assembly LH connector.

    2. Disconnect the L81 rear combination light assembly RH connector.

    3. Disconnect the L86 rear light lens and body LH connector.

    4. Disconnect the L90 rear light lens and body RH connector.

    5. Disconnect the L71 center stop light wire connector.

    6. Disconnect the A11 skid control ECU assembly connector.

    7. Disconnect the G90 vehicle approaching speaker controller connector.

    8. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L111-1 (OUT) or A11-14 (STP2) - Body ground Always 10 kΩ or higher

    10. Connect the L111 No. 3 semiconductor power integration ECU connector.

    11. Connect the G90 vehicle approaching speaker controller connector.

    12. Connect the A11 skid control ECU assembly connector.

    13. Connect the L71 center stop light wire connector.

    14. Connect the L90 rear light lens and body RH connector.

    15. Connect the L86 rear light lens and body LH connector.

    16. Connect the L81 rear combination light assembly RH connector.

    17. Connect the L82 rear combination light assembly LH connector.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO POWER INTEGRATION SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  41. CHECK HARNESS AND CONNECTOR (NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU - STOP LIGHT SWITCH ASSEMBLY)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

      Standard
      There is no malfunction

    2. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    3. Disconnect the A12 skid control ECU assembly connector.

    4. Disconnect the A77 hybrid vehicle control ECU assembly connector.

    5. Disconnect the L31 certification ECU (smart key ECU assembly) connector.

    6. Disconnect the G82 shift control ECU connector.

    7. Disconnect the A3 stop light switch assembly connector.

    8. Check the connector case and the terminal for deformation and corrosion.

      Standard
      No deformation or corrosion

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L111-10 (STP) - Body ground Brake pedal depressed Below 1.5 V

    10. Connect the A3 stop light switch assembly connector.

    11. Connect the G82 shift control ECU connector.

    12. Connect the L31 certification ECU (smart key ECU assembly) connector.

    13. Connect the A77 hybrid vehicle control ECU assembly connector.

    14. Connect the A12 skid control ECU assembly connector.

    15. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  42. CHECK HARNESS AND CONNECTOR (NO. 3 SEMICONDUCTOR POWER INTEGRATION ECU - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the L111 No. 3 semiconductor power integration ECU connector.

    2. Disconnect the A3 stop light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L111-10 (STP) - A3-2 (L) Always Below 1 Ω
      L111-10 (STP) or A3-2 (L) - Body ground Always 10 kΩ or higher

    4. Connect the A3 stop light switch assembly connector.

    5. Connect the L111 No. 3 semiconductor power integration ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR