Click here

POP UP HOOD LIFTER(for Rear Side) DISPOSAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any pop up hood lifter, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B004W1I

    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

    Tip:

    When scrapping a vehicle equipped with an SRS or disposing of the No. 2 pop up hood lifter assembly LH assembly, be sure to deploy the No. 2 pop up hood lifter assembly LH first in accordance with the procedure described below. If any abnormality occurs with the No. 2 pop up hood lifter assembly LH deployment, contact the Service Dept. of the distributor.

  2. Click here

    DISPOSE OF NO. 2 POP UP HOOD LIFTER ASSEMBLY LH (When Installed in Vehicle)

    Note:

    • When disposing of a No. 2 pop up hood lifter assembly LH, use an unneeded vehicle to deploy the No. 2 pop up hood lifter assembly LH.

    • Be sure to observe the following procedure when deploying the No. 2 pop up hood lifter assembly LH.

    Tip:

    Prepare a battery as the power source to deploy the No. 2 pop up hood lifter assembly LH.


    1. B004YBUN08

      Check the function of SST.

      Click here

      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the front fender reinforcement top sub-assembly LH.

      Click here

      Click here

    6. B004ROFC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B004RMI Slide

      Disconnect pop up hood lifter connector.

      Note:

      When disconnecting any pop up hood lifter connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note:

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the No. 2 pop up hood lifter assembly LH connector.

    7. Install SST.


      1. B004TV3N01

        Connect SST to the No. 2 pop up hood lifter assembly LH connector.

        09082-00820
        CAUTION:
        B004UQ1

        • Do not deploy if the No. 2 pop up hood lifter assembly LH is loose.

        • If deployed while the No. 2 pop up hood lifter assembly LH is loose, the No. 2 pop up hood lifter assembly LH may fly off and cause serious injuries.

      2. Connect SST together (09082-00700 and 09082-00820).

        Note:

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.

      3. B004TTMC02
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the engine compartment of the vehicle.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    8. Close the engine hood.

      CAUTION:

      Check that the engine hood is locked.

    9. Deploy the No. 2 pop up hood lifter assembly LH.


      1. Check that no one is within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press SST activation switch to deploy the No. 2 pop up hood lifter assembly LH.

        CAUTION:
        B004T50

        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        Tip:

        The No. 2 pop up hood lifter assembly LH is deployed as the LED of SST activation switch comes on.

    10. Remove the No. 2 pop up hood lifter assembly LH.

      Click here

      CAUTION:

      • B004WMZ

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004WKZ

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004T94

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the No. 2 pop up hood lifter assembly LH in a plastic bag.

    11. Place the No. 2 pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.

      CAUTION:

      • B004VBR

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004RXG

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004RC1

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B004YGR

        Never dispose of a No. 2 pop up hood lifter assembly LH with an undeployed No. 2 pop up hood lifter assembly LH.

      • If an undeployed No. 2 pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.

  3. Click here

    DISPOSE OF NO. 2 POP UP HOOD LIFTER ASSEMBLY LH (When not Installed in Vehicle)

    Note:

    Be sure to observe the following procedure when deploying the No. 2 pop up hood lifter assembly LH.

    Tip:

    Prepare a battery as the power source to deploy the No. 2 pop up hood lifter assembly LH.


    1. B004YBUN08

      Check the function of SST.

      Click here

      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the No. 2 pop up hood lifter assembly LH.

      Click here

    6. B004YEZC01
      *1 Pop Up Hood Cover

      Remove the pop up hood cover.

    7. Install SST.


      1. B004TT2N01

        Connect SST to the No. 2 pop up hood lifter assembly LH.

        09082-00820
    8. B004WQQC91
      *a Wire Diameter
      B004VGX Stripped Wire

      Using braided wire, tie down the No. 2 pop up hood lifter assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more
      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the No. 2 pop up hood lifter assembly LH, it may snap when the No. 2 pop up hood lifter assembly LH is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).

      Tip:

      To calculate the area of the cross-sectional area of stripped wire:

      Cross sectional area = 3.14 x (Diameter)2 / 4


      1. B004W9QC02
        *a Width
        *b Inner Diameter
        *c extended section

        Position the No. 2 pop up hood lifter assembly LH inside the tire as shown in the illustration.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)
        CAUTION:
        B004SKFC01
        *a Extended Section
        *b Remove looseness

        • Do not install the No. 2 pop up hood lifter assembly LH with the extended section facing outside.

        • When securing the No. 2 pop up hood lifter assembly LH, make sure there is no looseness in the wire harness.

        • If the extended section is facing outside or the wire harness is loosely wrapped, the deployed No. 2 pop up hood lifter assembly LH and tire may fly off and cause serious injuries.

        Note:

        The tire may be damaged by the No. 2 pop up hood lifter assembly LH deployment, so use unneeded tire.

        Tip:

        Through the wire to pop up hood lifter installation hole.

    9. Place the tires.


      1. B004RM8C02
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the No. 2 pop up hood lifter assembly LH is tied.

      2. Place at least 2 tires onto the tire to which the No. 2 pop up hood lifter assembly LH is tied. The top tire should have a wheel installed.

        Note:

        • Do not place SST connector under the tire because it could be damaged.

        • The wheel and tires may be damaged by the No. 2 pop up hood lifter assembly LH deployment, so use an unneeded wheel and tires.

      3. B004T13

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the No. 2 pop up hood lifter assembly LH is deployed.

    10. Install SST.


      1. B004YDNC02
        *a 10 m (32.8 ft.) or more

        Connect SST together (09082-00700 and 09082-00820).

        09082-00700
        Note:

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the No. 2 pop up hood lifter assembly LH tied down to the tire.

    11. Deploy the No. 2 pop up hood lifter assembly LH.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the No. 2 pop up hood lifter assembly LH is tied.

      3. Press SST activation switch to deploy the No. 2 pop up hood lifter assembly LH.

        CAUTION:
        B004UO9

        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        Tip:

        The No. 2 pop up hood lifter assembly LH is deployed as the LED of SST activation switch comes on.

    12. Dispose of the No. 2 pop up hood lifter assembly LH.

      CAUTION:

      • B004VBR

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004RXG

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004RC1

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B004YGR

        Never dispose of a No. 2 pop up hood lifter assembly LH with an undeployed No. 2 pop up hood lifter assembly LH.

      • If an undeployed No. 2 pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the No. 2 pop up hood lifter assembly LH from the tire.

      2. Place the No. 2 pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.