CURTAIN SHIELD AIRBAG ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B004V8C

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the curtain shield airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When Installed to Vehicle)

    Note


    • When disposing of a curtain shield airbag assembly LH, use an unneeded vehicle to deploy the airbag.

    • Be sure to perform the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B004YBUN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal

      Click here

      CAUTION:

      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the roof headlining assembly.

      Click here

    6. B004YLMC01
      *a Lock Button
      B004VGX Protective Tape
      B004RMI Release in this Direction

      Disconnect the curtain shield airbag assembly LH connector.


      1. Using a screwdriver, release the lock button and disconnect the airbag connector.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

        Tech Tips

        Tape the screwdriver tip before use.

    7. Install SST.


      1. B004VK0N01

        After connecting the following SST to each other, connect them to the curtain shield airbag assembly LH.

        SST
        09082-00802   ( 09082-10801, 09082-20801 )

      2. Connect SST together (09082-00700 and 09082-10801).

        SST
        09082-00700

        Note

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.

        CAUTION:


        • B004XN6

          Do not deploy the curtain shield airbag assembly LH if it rattles due to looseness and the tightening bolts and clips, etc., for the inflator and deployment part of the curtain shield airbag assembly LH falling off.

        • Do not deploy the curtain shield airbag assembly LH if the deployment part fell off.

        • If the curtain shield airbag assembly LH is deployed when it rattles or parts have fallen off, the curtain shield airbag assembly LH may fly off and cause serious injuries.

      3. B004XNKC47
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the rear side window of the vehicle.

      4. Maintaining sufficient clearance for SST wire harness in the rear side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B004TIQ

        Note

        Take care not to damage SST wire harness.

      5. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    8. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press SST activation switch to deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B004SHS

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    9. Remove the curtain shield airbag assembly LH.

      Click here

      CAUTION:


      • B004TK4

        The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004R78

        Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

      • If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004XVB

        Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

      • If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the curtain shield airbag assembly LH in a plastic bag.

    10. Dispose of the curtain shield airbag assembly LH.


      1. Place the curtain shield airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B004SWC

          The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B004R82

          Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

        • If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

        • B004T3R

          Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

        • If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B004YL0

          Never dispose of a curtain shield airbag assembly LH with an undeployed airbag.

        • If an undeployed curtain shield airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY LH (When not Installed to Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B004YBUN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:

      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the curtain shield airbag assembly LH.

      Click here

    6. B004WKLC01
      *a Cut Here

      Cut off the deployment section of the curtain shield airbag assembly LH.

      CAUTION:

      B004T3R

      • Wear safety glasses and gloves.

      • The dust may enter the eyes or be breathed in.

    7. B004WQQC91
      *a Wire Diameter
      B004VGX Stripped Wire Cross Sectional Area

      Using braided wire, tie down the curtain shield airbag assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the curtain shield airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. B004YADC01
        *a Width
        *b Inner Diameter
        *c Outlet

        Position the curtain shield airbag assembly LH inside the tire with the outlet facing inside.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tire may be damaged by the airbag deployment, so use an unneeded tire.

    8. Install SST.


      1. B004UWPN01

        After connecting the following SST to each other, connect them to the curtain shield airbag assembly LH.

        SST
        09082-00802   ( 09082-10801, 09082-20801 )

    9. Place the tires.


      1. B004WDPC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the curtain shield airbag assembly LH is tied.

        Minimum Tire Size
        Width
        185 mm (7.28 in.)
        Inner Diameter
        360 mm (1.18 ft.)

        Note

        Do not place SST connector under the tire because it could be damaged.

      2. Place at least 2 tires onto the tire to which the curtain shield airbag assembly LH is tied. The top tire should have a wheel installed.

        Note

        The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.

      3. B004T13

        Tie the tires together with 2 wires.

    10. Install SST.


      1. B004XNFC01
        *a 10 m (32.8 ft.) or more

        Connect SST together (09082-00700 and 09082-10801).

        SST
        09082-00700

        Note

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    11. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag assembly LH is tied.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B004UX5

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    12. Dispose of the curtain shield airbag assembly LH.

      CAUTION:


      • B004SWC

        The curtain shield airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004R82

        Do not apply water etc. to a curtain shield airbag assembly LH with a deployed airbag.

      • If water is applied to the curtain shield airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004T3R

        Always wear safety glasses and gloves when handling a deployed curtain shield airbag assembly LH.

      • If the curtain shield airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B004YL0

        Never dispose of a curtain shield airbag assembly LH with an undeployed airbag.

      • If an undeployed curtain shield airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the curtain shield airbag assembly LH from the tire.

      2. Place the curtain shield airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.