Click here

REAR SEAT SIDE AIRBAG ASSEMBLY(for Power Seat) DISPOSAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:

    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • B004V8C

      If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

    Tip:

    When scrapping a vehicle equipped with an SRS or disposing of the rear seat airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. Click here

    DISPOSE OF REAR SEAT AIRBAG ASSEMBLY LH (When Installed to Vehicle)

    Note:

    • When disposing of the rear seat airbag assembly, use an unneeded vehicle to deploy the airbag.

    • Be sure to perform the following procedure when deploying the airbag.

    Tip:

    Prepare a battery as the power source to deploy the airbag.


    1. B004YBUN08

      Check the function of SST.

      Click here

      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the rear seat cushion assembly LH.

      Click here

    6. Install SST.


      1. B004VHON01

        Connect SST to the rear seat airbag assembly LH.

        09082-00820
        CAUTION:
        B004WD9

        • Do not deploy if the rear seat airbag assembly LH is loose.

        • If deployed while the rear seat airbag assembly LH is loose, the rear seat airbag assembly LH may fly off and cause serious injuries.

      2. Connect SST together (09082-00700 and 09082-00820).

        09082-00700
        Note:

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.

      3. B004RGCC09
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the rear side window of the vehicle.

      4. While maintaining sufficient clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:
        B004TIQ

        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        Note:

        Take care not to damage SST wire harness.

      5. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press SST activation switch to deploy the airbag.

        CAUTION:
        B004SHS

        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        Tip:

        The airbag is deployed as the LED of SST activation switch comes on.

    8. Remove the rear seat airbag assembly LH.

      Click here

      CAUTION:

      • B004THT

        The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004RTN

        Do not apply water etc. to a rear seat airbag assembly LH with a deployed airbag.

      • If water is applied to the rear seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004W5Y

        Always wear safety glasses and gloves when handling a deployed rear seat airbag assembly LH.

      • If the rear seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the rear seat airbag assembly LH in a plastic bag.

    9. Dispose of the rear seat airbag assembly LH.


      1. Place the rear seat airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:

        • B004YOI

          The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B004RYD

          Do not apply water etc. to a rear seat airbag assembly LH with a deployed airbag.

        • If water is applied to the rear seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

        • B004RPS

          Always wear safety glasses and gloves when handling a deployed rear seat airbag assembly LH.

        • If the rear seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B004SF7

          Never dispose of a rear seat airbag assembly LH with an undeployed airbag.

        • If an undeployed rear seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. Click here

    DISPOSE OF REAR SEAT AIRBAG ASSEMBLY LH (When not Installed to Vehicle)

    Note:

    Be sure to perform the following procedure when deploying the airbag.

    Tip:

    Prepare a battery as the power source to deploy the airbag.


    1. B004YBUN08

      Check the function of SST.

      Click here

      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the luggage compartment mat sub-assembly.

      Click here

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Click here

      CAUTION:
      B004UM0

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the rear seat airbag assembly LH.

      Click here

    6. B004WQQC91
      *a Wire Diameter
      B004VGX Stripped Wire

      Using braided wire, tie down the rear seat airbag assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more
      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the rear seat airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).

      Tip:

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2 / 4


      1. B004U33

        Install the 2 nuts to the rear seat airbag assembly LH.

      2. B004S8H

        Wind 2 or more wires around the stud bolts of the rear seat airbag assembly LH as shown in the illustration.

      3. B004WX7C01
        *a Width
        *b Inner Diameter
        *c Deployment Side

        Position the rear seat airbag assembly LH inside the tire with the airbag deployment side facing inward.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)
        CAUTION:
        B004Y8GC01
        *a Remove looseness
        B004VGX Deployment Side

        • Do not install the rear seat airbag assembly LH with the deployment side facing outside.

        • When securing the rear seat airbag assembly LH, make sure there is no looseness in the wire harness.

        • If the deployment side is facing outside or the wire harness is loosely wrapped, the deployed front seat airbag assembly LH and tire may fly off and cause serious injuries.

        Note:

        The tire may be damaged by the airbag deployment, so use an unneeded tires.

    7. Install SST.


      1. B004WX3N01

        Connect SST to the rear seat airbag assembly LH.

        09082-00820

    8. Place the tires.


      1. B004UTMC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the rear seat airbag assembly LH is tied.

      2. Place at least 2 tires onto the tire to which the rear seat airbag assembly LH is tied. The top tire should have a wheel installed.

        Note:

        • Do not place SST connector under the tire because it could be damaged.

        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

      3. B004T13

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.

    9. Install SST.


      1. B004TJKC01
        *a 10 m (32.8 ft.) or more

        Connect SST together (09082-00700 and 09082-00820).

        09082-00700
        Note:

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tires.

    10. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the rear seat airbag assembly LH is tied.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:
        B004UO9

        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        Tip:

        The airbag is deployed as the LED of SST activation switch comes on.

    11. Dispose of the rear seat airbag assembly LH.

      CAUTION:

      • B004YOI

        The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B004RYD

        Do not apply water etc. to a rear seat airbag assembly LH with a deployed airbag.

      • If water is applied to the rear seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B004RPS

        Always wear safety glasses and gloves when handling a deployed rear seat airbag assembly LH.

      • If the rear seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B004SF7

        Never dispose of a rear seat airbag assembly LH with an undeployed airbag.

      • If an undeployed rear seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the rear seat airbag assembly LH from the tire.

      2. Place the rear seat airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.