THEFT DETERRENT SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use this procedure to troubleshoot the theft deterrent system.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT

  2. CUSTOMER PROBLEM ANALYSIS


    1. Interview the customer to confirm the trouble.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. READ OUT AND SAVE OPERATION HISTORY

    Note


    • If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.

    • The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.


    1. Read out and save operation history using the GTS.

      Click here


      Body Electrical > Main Body > Utility
      Tester Display
      Operation History
      Result
      Proceed to
      NEXT

    NEXT

  4. PRE-CHECK


    1. Measure the battery voltage.

      Standard voltage
      11 to 14 V (power switch off)

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

    2. Check the fuses and relays.

    3. Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

      Result
      Proceed to
      NEXT

    NEXT

  5. SYMPTOM SIMULATION

    Result
    Proceed to
    NEXT

    NEXT

  6. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the CAN communication system is functioning normally.

      Click here

      Result
      Proceed to
      CAN communication system DTC is not output
      CAN communication system DTC is output

    CAN communication system DTC is output

    GO TO CAN COMMUNICATION SYSTEM Click here

    CAN communication system DTC is not output

  7. INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the LIN communication system is functioning normally.

      Click here

      Result
      Proceed to
      LIN communication system DTC is not output
      LIN communication system DTC is output

    LIN communication system DTC is output

    GO TO LIN COMMUNICATION SYSTEM Click here

    LIN communication system DTC is not output

  8. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. Refer to the power door lock control system.

      Click here

      Result
      Proceed to
      Power door lock control system is normal
      Power door lock control system is abnormal

    Power door lock control system is abnormal

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    Power door lock control system is normal

  9. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Refer to the wireless door lock control system.

      Click here

      Result
      Result Proceed to
      Wireless door lock control system is normal A
      Wireless door lock control system is abnormal B

    B

    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM Click here

    A

  10. CHECK ENTRY AND START SYSTEM (for Entry Function)


    1. Refer to the entry and start system (for Entry Function).

      Click here

      Result
      Proceed to
      Entry and start system (for Entry Function) is normal
      Entry and start system (for Entry Function) is abnormal

    Entry and start system (for Entry Function) is abnormal

    GO TO ENTRY AND START SYSTEM (for Entry Function) Click here

    Entry and start system (for Entry Function) is normal

  11. CHECK ENTRY AND START SYSTEM (for Start Function)


    1. Refer to the entry and start system (for Start Function).

      Click here

      Result
      Proceed to
      Entry and start system (for Start Function) is normal
      Entry and start system (for Start Function) is abnormal

    Entry and start system (for Start Function) is abnormal

    GO TO ENTRY AND START SYSTEM (for Start Function) Click here

    Entry and start system (for Start Function) is normal

  12. CHECK LIGHTING SYSTEM (EXT)


    1. Refer to the lighting system (EXT).

      Click here

      Result
      Proceed to
      Lighting system (EXT) is normal
      Lighting system (EXT) is abnormal

    Lighting system (EXT) is abnormal

    GO TO LIGHTING SYSTEM (EXT) Click here

    Lighting system (EXT) is normal

  13. CHECK LIGHTING SYSTEM (INT)


    1. Refer to the lighting system (INT).

      Click here

      Result
      Proceed to
      Lighting system (INT) is normal
      Lighting system (INT) is abnormal

    Lighting system (INT) is abnormal

    GO TO LIGHTING SYSTEM (INT) Click here

    Lighting system (INT) is normal

  14. CHECK POWER TRUNK LID SYSTEM


    1. Refer to the power trunk lid system.

      Click here

      Result
      Proceed to
      Power trunk lid system is normal
      Power trunk lid system is abnormal

    Power trunk lid system is abnormal

    GO TO POWER TRUNK LID SYSTEM Click here

    Power trunk lid system is normal

  15. CHECK HORN SYSTEM


    1. Refer to the horn system.

      Click here

      Result
      Proceed to
      Horn system is normal
      Horn system is abnormal

    Horn system is abnormal

    GO TO HORN SYSTEM Click here

    Horn system is normal

  16. CHECK FOR DTC*


    1. Check for DTCs.

      Click here


      Body Electrical > Main Body > Trouble Codes
      Result
      Proceed to
      DTCs are not output
      Theft deterrent system DTCs are output

    Theft deterrent system DTCs are output

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    DTCs are not output

  17. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table (Fault can be simulated) A
      Fault is not listed in Problem Symptoms Table (Fault can not be simulated) B
      Fault is listed in Problem Symptoms Table C

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    C

    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

    A

  18. PERFORM TROUBLESHOOTING ACCORDING TO MALFUNCTION SYMPTOM*


    1. System Description.

      Click here

    2. Terminals of ECU.

      Click here

    3. Data List / Active Test.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  19. ADJUST, REPAIR OR REPLACE

    Result
    Proceed to
    NEXT

    NEXT

  20. CONFIRMATION TEST

    Result
    Proceed to
    NEXT

    NEXT

    END