LIN COMMUNICATION SYSTEM, Diagnostic DTC:B1206, B1273, B2321, B2322, B2323, B2324, B232A, B232B

DTC Code DTC Name
B1206 P/W Master Switch Communication Stop
B1273 Sliding Roof ECU Communication Stop
B2321 Driver Side Door ECU Communication Stop
B2322 Front Passenger Side Door ECU Communication Stop
B2323 Rear Door RH ECU Communication Stop
B2324 Rear Door LH ECU Communication Stop
B232A Lost Communication with RR Door Quarter Window Sunshade ECU
B232B Lost Communication with RL Door Quarter Window Sunshade ECU

DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly, front power window regulator motor assembly LH, front power window regulator motor assembly RH, rear power window regulator motor assembly LH, rear power window regulator motor assembly LH, sliding roof drive gear sub-assembly*1, rear side window curtain assembly LH*2, rear side window curtain assembly RH*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1206 P/W Master Switch Communication Stop No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Front multiplex network door ECU LH

  • Multiplex network master switch assembly

  • Harness or connector
B1273 Sliding Roof ECU Communication Stop No communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Front multiplex network door ECU LH

  • Sliding roof drive gear sub-assembly

  • Harness or connector

  • w/ Sliding Roof System
B2321 Driver Side Door ECU Communication Stop No communication between the front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Front multiplex network door ECU LH

  • Front power window regulator motor assembly LH

  • Harness or connector
B2322 Front Passenger Side Door ECU Communication Stop No communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Front multiplex network door ECU RH

  • Front power window regulator motor assembly LH

  • Harness or connector
B2323 Rear Door RH ECU Communication Stop No communication between the rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Front multiplex network door ECU LH

  • Rear power window regulator motor assembly LH

  • Harness or connector
B2324 Rear Door LH ECU Communication Stop No communication between the rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Rear multiplex network door ECU RH

  • Rear power window regulator motor assembly RH

  • Harness or connector
B232A Lost Communication with RR Door Quarter Window Sunshade ECU No communication between the rear side window curtain assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Rear side window curtain assembly RH

  • Harness or connector

  • w/ Side Window Curtain
B232B Lost Communication with RL Door Quarter Window Sunshade ECU No communication between the rear side window curtain assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU)

  • Rear side window curtain assembly LH

  • Harness or connector

  • w/ Side Window Curtain

WIRING DIAGRAM


  1. for LHD:

    B004Y5IE01
    B004YCZE01
    B004SO7E01
    B004Y4HE01

  2. for RHD:

    B004ST0E02
    *1 Instrument Panel Junction Block Assembly
    *2 Main Body ECU (Multiplex Network Body ECU)
    *3 LIN Communication Line
    B004YDPE02
    B004S3AE02
    B004U4UE02

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the power switch off to troubleshoot:

    Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

Tech Tips

DTC B2325 is output when the communication between all of the following components and main body ECU (multiplex network body ECU) stops.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs
      Result
      Result Proceed to
      for LHD A
      for RHD B

    B

    CHECK FOR DTC Click here

    A

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC is not output A
      DTC B1206, B1273*1, B2321, B2322, B2323, B2324, B232A*2 and B232B*2 are output B
      DTC B1206 and B2321 are output C
      DTC B2322, B2324, B232A2* and B232B*2 are output D
      DTC B1206 is output E
      DTC B1273*1 is output F
      DTC B2321 is output G
      DTC B2322 is output H
      DTC B2323 is output I
      DTC B2324 is output J
      DTC B232A*2 is output K
      DTC B232B*2 is output L
      *1: w/ Sliding Roof System
      *2: w/ Hands Free Power Back Door

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    E

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

    G

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    H

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    I

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    J

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    K

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY RH) Click here

    L

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY LH) Click here

    B

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Disconnect the 5A instrument panel junction block assembly connector.

      B004U9YC12
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - 5A-40 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the main body ECU (multiplex network body ECU) connector.

    2. Disconnect the I5 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-16 - I5-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BODY GROUND)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-34 - H2-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the I5 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-34 - I5-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the I5 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-34 - I5-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY)


    1. Disconnect the I5 multiplex network master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I5-11 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BODY GROUND)


    1. Disconnect the I5 multiplex network master switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I5-12 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

  11. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the I5 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-9 (SGND) - I5-12 (GND) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the I5 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-12 (LIN2) - I5-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)


    1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    2. Reconnect the instrument panel junction block assembly connectors.

    3. Disconnect the N4 sliding roof drive gear sub-assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - N4-7 (MPX1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

    OK

  14. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - BATTERY AND BODY GROUND)


    1. Disconnect the N4 sliding roof drive gear sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N4-2 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N4-1 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the N4 sliding roof drive gear sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-20 - N4-7 (MPX1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  16. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-34 - H21-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    OK

  17. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY)


    1. Disconnect the H21 front power window regulator motor assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H21-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY) Click here

    OK

  18. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BODY GROUND)


    1. Disconnect the H21 front power window regulator motor assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H21-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - FRONT MULTIPLEX NETWORK DOOR ECU LH) Click here

  19. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H31-6 (BDR) - Body ground IG OFF 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-5 (BDR) - H21-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  21. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - FRONT MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the H21 front power window regulator motor assembly LH connector.

    2. Disconnect the H31 front multiplex network door ECU LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H21-1 - H31-1 (GND) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  22. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-13 (LIN3) - H21-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  23. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-19 - H2-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    OK

  24. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY)


    1. Disconnect the H2 front power window regulator motor assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H2-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY) Click here

    OK

  25. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BODY GROUND)


    1. Disconnect the H2 front power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

  26. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH AND BODY GROUND)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-2 (PWE) - H2-1 (GND) Always Below 1 Ω
      H12-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  27. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H12-6 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  28. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-5 (BDRJ) - H2-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  29. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-13 (LIN3) - H2-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  30. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the 5A instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-11 (LIN1) - 5A-19 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  31. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-19 - K1-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    OK

  32. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY)


    1. Disconnect the K1 rear power window regulator motor assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K1-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - BATTERY) Click here

    OK

  33. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BODY GROUND)


    1. Disconnect the K1 rear power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K1-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

  34. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH AND BODY GROUND)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-2 (PWE) - K1-1 (GND) Always Below 1 Ω
      K7-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  35. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - BATTERY)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K7-4 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  36. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-3 (BDRJ) - K1-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  37. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-23 (LIN3) - K1-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  38. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the 5A instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-22 (LIN1) - 5A-19 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  39. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-35 - K15-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    OK

  40. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY)


    1. Disconnect the K15 rear power window regulator motor assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K15-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY) Click here

    OK

  41. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BODY GROUND)


    1. Disconnect the K15 rear power window regulator motor assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K15-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

  42. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH AND BODY GROUND)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-2 (PWE) - K15-1 (GND) Always Below 1 Ω
      K21-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  43. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K21-4 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  44. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-3 (BDRJ) - K15-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  45. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-23 (LIN3) - K15-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  46. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the 5H instrument panel junction block assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-22 (LIN1) - 5H-35 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  47. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY RH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the L143 rear side window curtain assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-19 - L143-6 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  48. CHECK HARNESS AND CONNECTOR (REAR SIDE WINDOW CURTAIN ASSEMBLY RH - BATTERY AND BODY GROUND)


    1. Disconnect the L143 rear side window curtain assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L143-10 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L143-3 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR SIDE WINDOW CURTAIN ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  49. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the L144 rear side window curtain assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-19 - L144-6 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  50. CHECK HARNESS AND CONNECTOR (REAR SIDE WINDOW CURTAIN ASSEMBLY LH - BATTERY AND BODY GROUND)


    1. Disconnect the L144 rear side window curtain assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L144-10 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L144-3 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR SIDE WINDOW CURTAIN ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  51. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC is not output A
      DTC B1206, B1273*1, B2321, B2322, B2323, B2324, B232A*2 and B232B*2 are output B
      DTC B1206 and B2321 are output C
      DTC B1273*1, B2322, B2324, B232A*2 and B232B*2 are output D
      DTC B1206 is output E
      DTC B1273 is output F
      DTC B2321 is output G
      DTC B2322 is output H
      DTC B2323 is output I
      DTC B2324 is output J
      DTC B232A*2 is output K
      DTC B232B*2 is output L
      *1: w/ Sliding Roof System
      *2: w/ Side Window Curtain

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    E

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

    G

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    H

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    I

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    J

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    K

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY RH) Click here

    L

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY LH) Click here

    B

  52. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Disconnect the 5A instrument panel junction block assembly connectors.

      B004U9YC12
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - 5A-40 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

  53. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the main body ECU (multiplex network body ECU) connector.

    2. Disconnect the I2 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-16 - I2-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    OK

  54. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BODY GROUND)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  55. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the I2 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-33 - I2-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  56. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - H21-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  57. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the I2 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-33 - I2-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY) Click here

    OK

  58. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY)


    1. Disconnect the I2 multiplex network master switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I2-11 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  59. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BODY GROUND)


    1. Disconnect the I2 multiplex network master switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I2-12 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

  60. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the I2 multiplex network master switch assembly connector.

    2. Disconnect the H12 front multiplex network door ECU RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I2-12 (GND) - H12-9 (SGND) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  61. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the I2 multiplex network master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-12 (LIN2) - I2-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  62. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the N4 sliding roof drive gear sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - N4-7 (MPX1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  63. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - BATTERY AND BODY GROUND)


    1. Disconnect the N4 sliding roof drive gear sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N4-2 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N4-1 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  64. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-33 - H2-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    OK

  65. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY)


    1. Disconnect the H2 front power window regulator motor assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H2-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY) Click here

    OK

  66. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BODY GROUND)


    1. Disconnect the H2 front power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOOR ECU RH) Click here

  67. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-6 (BDR) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  68. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-5 (BDRJ) - H2-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  69. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOOR ECU RH)


    1. Disconnect the H2 front power window regulator motor assembly RH connector.

    2. Disconnect the H12 front multiplex network door ECU RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-1 - H12-1 (GND) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  70. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the H12 front multiplex network door ECU RH connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H12-13 (LIN3) - H2-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  71. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - H21-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    OK

  72. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY)


    1. Disconnect the H21 front power window regulator motor assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H21-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY) Click here

    OK

  73. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BODY GROUND)


    1. Disconnect the H21 front power window regulator motor assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H21-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

  74. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH AND BODY GROUND)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-2 (PWE) - H21-1 (GND) Always Below 1 Ω
      H31-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  75. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H31-6 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  76. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-5 (BDRJ) - H21-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  77. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the H31 front multiplex network door ECU LH connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H31-13 (LIN3) - H21-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  78. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the H31 front multiplex network door ECU LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - H31-11 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  79. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the 5H instrument panel junction block assembly connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5H-34 - K1-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    OK

  80. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY)


    1. Disconnect the K1 rear power window regulator motor assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K1-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - BATTERY) Click here

    OK

  81. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BODY GROUND)


    1. Disconnect the K1 rear power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K1-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

  82. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH AND BODY GROUND)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-2 (PWE) - K1-1 (GND) Always Below 1 Ω
      K7-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  83. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - BATTERY)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K7-4 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  84. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-3 (BDRJ) - K1-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  85. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the K1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-23 (LIN3) - K1-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  86. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the K7 rear multiplex network door ECU RH connector.

    2. Disconnect the 5H instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K7-22 (LIN1) - 5H-34 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  87. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - K15-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    OK

  88. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY)


    1. Disconnect the K15 rear power window regulator motor assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K15-2 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY) Click here

    OK

  89. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BODY GROUND)


    1. Disconnect the K15 rear power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K15-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

  90. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH AND BODY GROUND)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-2 (PWE) - K15-1 (GND) Always Below 1 Ω
      K21-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  91. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - BATTERY)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K21-4 (BDR) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  92. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-3 (BDRJ) - K15-2 (B) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  93. CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the K21 rear multiplex network door ECU LH connector.

    2. Disconnect the K15 rear power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-23 (LIN3) - K15-9 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  94. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the K21 rear multiplex network gateway ECU LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - K21-22 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  95. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY RH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the L143 rear side window curtain assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-19 - L143-6 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  96. CHECK HARNESS AND CONNECTOR (REAR SIDE WINDOW CURTAIN ASSEMBLY RH - BATTERY AND BODY GROUND)


    1. Disconnect the L143 rear side window curtain assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L143-10 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L143-3 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR SIDE WINDOW CURTAIN ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  97. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR SIDE WINDOW CURTAIN ASSEMBLY LH)


    1. Disconnect the 5A instrument panel junction block assembly connector.

    2. Disconnect the L144 rear side window curtain assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5A-40 - L144-6 (LIN) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  98. CHECK HARNESS AND CONNECTOR (REAR SIDE WINDOW CURTAIN ASSEMBLY LH - BATTERY AND BODY GROUND)


    1. Disconnect the L144 rear side window curtain assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L144-10 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L144-3 (B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR SIDE WINDOW CURTAIN ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR