SUB BATTERY RELAY INSTALLATION

PROCEDURE


  1. INSTALL BACKUP RELAY


    1. Attach the claw and install the backup relay to the relay block assembly.

    2. Connect the connector to the backup relay.

    3. Install the backup relay to the relay block assembly with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    4. Install the bolt and nut to the backup relay terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    5. Attach the 3 claws and connect the relay block assembly to the luggage room relay block (luggage room relay block upper side).

    6. Attach the 6 claws and install the relay block lower cover to the luggage room relay block (luggage room relay block lower side).

    7. Attach the clamp and connect the 3 tie wraps the luggage room relay block (luggage room relay block lower side).

  2. INSTALL LUGGAGE ROOM RELAY BLOCK


    1. w/ Dynamic Rear Steering:


      1. B004TJCC01
        *a Ground Wire Bolt
        *b Ground Wire

        Pull down the lock lever and connect the connector of the DRS control ECU as shown in the illustration.

      2. Install the ground wire with the bolt.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      3. Attach the 2 clamps and connect the luggage room relay block harness to the luggage room panel.

    2. Attach the 2 clamps and connect the luggage room relay block harness to the luggage room panel.

    3. B004UUY

      Pull down the lock lever and connect the connector as shown in the illustration.

    4. Attach the 3 clamps and connect the luggage room relay harness to the luggage room panel.

    5. Install the relay block cover.

    6. Attach the clamp and claw to the luggage room relay block.

    7. Install the luggage room relay block with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    8. Connect the positive (+) sub-battery terminal to the sub-battery module assembly with the nut.

      Torque:
      8.7 N*m  { 89 kgf*cm, 77 in.*lbf }

  3. INSTALL CONNECTOR COVER

    Click here

  4. INSTALL BATTERY CARRIER ASSEMBLY


    1. Install the battery carrier assembly to the luggage room panel with the 6 bolts.

      Torque:
      19.5 N*m  { 199 kgf*cm, 14 ft.*lbf }

  5. INSTALL BATTERY CARRIER CATCH BRACKET SUB-ASSEMBLY


    1. Install the battery carrier catch bracket sub-assembly to the luggage room panel with the 4 nuts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  6. INSTALL REAR LUGGAGE COMPARTMENT TRAY BRACKET RH

    Click here

  7. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  8. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH

    Click here

  9. INSTALL REAR LUGGAGE COMPARTMENT TRIM COVER

    Click here

  10. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  11. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  12. INSTALL INNER LOWER LUGGAGE COMPARTMENT TRIM COVER

    Click here

  13. INSTALL REAR FLOOR FINISH PLATE

    Click here

  14. INSTALL ROPE HOOK ASSEMBLY

    Click here

  15. INSTALL SIDE TRIM BOX

    Click here

  16. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH

    Click here

  17. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  18. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  19. INSTALL AUXILIARY BATTERY

    Click here

  20. INSTALL TOOL BOX

    Click here

  21. INSTALL REAR COOLING UNIT ASSEMBLY (w/ Rear Cooler)

    Click here

  22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  23. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here