ULTRASONIC SENSOR(for Front) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT ULTRASONIC SENSOR CLIP

    Note


    • Installing the front ultrasonic sensor clip with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

    • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

    Tech Tips

    Use the same procedure for all front ultrasonic sensor clip.


    1. Clean the front bumper assembly surface.


      1. Remove any remaining double-sided tape from the front bumper assembly.

      2. Wipe off any tape adhesive residue with cleaner.

    2. B004YNEC06
      *a Scribed line
      B004VH3 Primer Application

      Apply primer to front bumper assembly on the installation area of the front ultrasonic sensor clip using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the front ultrasonic sensor clip has been attached.

    3. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    4. Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.

    5. Remove the peeling paper of the new front ultrasonic sensor clip trying not to touch the adhesional surface.

      Note

      After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves

    6. B004T63C04
      *a Scribed Line

      Align the front ultrasonic sensor clip with the scribed line on the front bumper assembly and install it as shown in the illustration.

      Note

      The application strength of the front ultrasonic sensor clip will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

      Tech Tips

      Apply pressure so that it does not lift up from the front bumper assembly.

  2. INSTALL FRONT CENTER ULTRASONIC SENSOR


    1. B004S71

      Attach the claw to install the front center ultrasonic sensor.

      Note


      • When reusing the sensor, make sure that each sensor is returned to its original position.

      • Check that the claw is securely fitted.

      • B004VXMC08
        B004VGX Microphone Surface

        Do not push microphone surface.

  3. INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

    Note


    • Installing the front corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

    • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.


    1. Clean the front bumper assembly surface.


      1. Remove any remaining double-sided tape from the front bumper assembly.

      2. Wipe off any tape adhesive residue with cleaner.

    2. B004XIAC04
      *a 30 mm (1.18 in.)

      Cover the sensor installation hole form the outside of the bumper cover with a 30 mm (1.18 in.) square piece of tape.

    3. B004V5FC04
      *a Scribed Line
      B004VH3 Primer Application

      Apply primer to front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.

    4. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    5. Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.

    6. Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

      Note

      After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves

    7. B004V51C04
      *a Scribed Line

      Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

      Note

      The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

      Tech Tips


      • Apply pressure so that it does not lift up from the front bumper assembly.

      • Pushing force: 30 N (3.0 kgf) for 3 seconds

  4. INSTALL FRONT CORNER ULTRASONIC SENSOR


    1. Attach the claw and install the front corner ultrasonic sensor.

      Note


      • When reusing the sensor, make sure that each sensor is returned to its original position.

      • Check that the claw is securely fitted.

      • B004VXMC09
        B004VGX Microphone Surface

        Do not push microphone surface.

      Tech Tips

      Align the connector with the protrusion of the mark when connecting it.

      B004SSKC04
      *a Protrusion of the mark

  5. INSTALL NO. 4 ENGINE ROOM WIRE

    Click here

  6. INSTALL FRONT BUMPER ASSEMBLY


    1. for Sport Package:

      Click here

    2. for except Sport Package:

      Click here

  7. ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

    Click here

  8. PERFORM CALIBRATION


    1. w/ Parking Support Brake System:

      Click here

    2. w/o Parking Support Brake System:

      Click here