PARKING SUPPORT ALERT SYSTEM, Diagnostic DTC:C1AED

DTC Code DTC Name
C1AED Rear Sensor Communication Malfunction

DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AED Rear Sensor Communication Malfunction An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the power switch is turned on (IG).

  • Rear ultrasonic sensor circuit

  • Harness or connector

  • Clearance warning ECU assembly

WIRING DIAGRAM

B004UWUE17

PROCEDURE


  1. INITIALIZE REAR CENTER ULTRASONIC SENSOR AND REAR CORNER ULTRASONIC SENSOR


    1. Initialize the rear center ultrasonic sensor and rear corner ultrasonic sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK DTC OUTPUT (C1AED)


    1. Check for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes

    2. Clear the DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs

    3. Recheck for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
      Result
      Result Proceed to
      DTC C1AED is output A
      No DTCs are output B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  3. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR [RR SENSOR])


    1. Disconnect the L18 clearance warning ECU assembly connector.

    2. Disconnect the O4 rear corner ultrasonic sensor (RR sensor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L18-22 (BOR) - O4-4 (BI) Always Below 1 Ω
      L18-24 (SOR) - O4-5 (SI) Always Below 1 Ω
      L18-23 (E1) - O4-6 (EI) Always Below 1 Ω
      L18-22 (BOR) or O4-4 (BI) - Body ground Always 10 kΩ or higher
      L18-24 (SOR) or O4-5 (SI) - Body ground Always 10 kΩ or higher
      L18-23 (E1) or O4-6 (EI) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR [RR SENSOR] - REAR CENTER ULTRASONIC SENSOR [RRC SENSOR])


    1. Disconnect the O4 rear corner ultrasonic sensor (RR sensor) connector.

    2. Disconnect the O3 rear center ultrasonic sensor (RRC sensor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-1 (BO) - O3-4 (BI) Always Below 1 Ω
      O4-2 (SO) - O3-5 (SI) Always Below 1 Ω
      O4-3 (EO) - O3-6 (EI) Always Below 1 Ω
      O4-1 (BO) or O3-4 (BI) - Body ground Always 10 kΩ or higher
      O4-2 (SO) or O3-5 (SI) - Body ground Always 10 kΩ or higher
      O4-3 (EO) or O3-6 (EI) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] - REAR CENTER ULTRASONIC SENSOR [RLC SENSOR])


    1. Disconnect the O3 rear center ultrasonic sensor (RRC sensor) connector.

    2. Disconnect the O2 rear center ultrasonic sensor (RLC sensor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O3-1 (BO) - O2-4 (BI) Always Below 1 Ω
      O3-2 (SO) - O2-5 (SI) Always Below 1 Ω
      O3-3 (EO) - O2-6 (EI) Always Below 1 Ω
      O3-1 (BO) or O2-4 (BI) - Body ground Always 10 kΩ or higher
      O3-2 (SO) or O2-5 (SI) - Body ground Always 10 kΩ or higher
      O3-3 (EO) or O2-6 (EI) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RLC SENSOR] - REAR CORNER ULTRASONIC SENSOR [RL SENSOR])


    1. Disconnect the O2 rear center ultrasonic sensor (RLC sensor) connector.

    2. Disconnect the O1 rear corner ultrasonic sensor (RL sensor) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O2-1 (BO) - O1-4 (BI) Always Below 1 Ω
      O2-2 (SO) - O1-5 (SI) Always Below 1 Ω
      O2-3 (EO) - O1-6 (EI) Always Below 1 Ω
      O2-1 (BO) or O1-4 (BI) - Body ground Always 10 kΩ or higher
      O2-2 (SO) or O1-5 (SI) - Body ground Always 10 kΩ or higher
      O2-3 (EO) or O1-6 (EI) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT REAR CORNER ULTRASONIC SENSOR (RR SENSOR)


    1. Remove rear corner ultrasonic sensor (RR sensor).

      Click here

    2. Inspect the rear corner ultrasonic sensor (RR sensor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR CORNER ULTRASONIC SENSOR (RR SENSOR) Click here

    OK

  8. INSPECT REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)


    1. Remove the rear center ultrasonic sensor (RRC sensor).

      Click here

    2. Inspect the rear center ultrasonic sensor (RRC sensor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR) Click here

    OK

  9. INSPECT REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)


    1. Remove the rear center ultrasonic sensor (RLC sensor).

      Click here

    2. Inspect the rear center ultrasonic sensor (RLC sensor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR CENTER ULTRASONIC SENSOR (RLC SENSOR) Click here

    OK

  10. INSPECT REAR CORNER ULTRASONIC SENSOR (RL SENSOR)


    1. Remove the rear corner ultrasonic sensor (RL sensor).

      Click here

    2. Inspect the rear corner ultrasonic sensor (RL sensor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR CORNER ULTRASONIC SENSOR (RL SENSOR) Click here

    OK

  11. REPLACE REAR CORNER ULTRASONIC SENSOR (RR SENSOR)


    1. Replace the rear corner ultrasonic sensor (RR sensor) with a known good one.

      Click here

      Tech Tips

      All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.

      Result
      Proceed to
      NEXT

    NEXT

  12. CHECK DTC OUTPUT (C1AED)


    1. Clear the DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
      Result
      Result Proceed to
      DTC C1AED is output A
      No DTCs are output B

    B

    END (REAR CORNER ULTRASONIC SENSOR [RR SENSOR] WAS DEFECTIVE)

    A

  13. REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)


    1. Replace the rear center ultrasonic sensor (RRC sensor) with a known good one.

      Click here

      Tech Tips

      All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.

      Result
      Proceed to
      NEXT

    NEXT

  14. CHECK DTC OUTPUT (C1AED)


    1. Clear the DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
      Result
      Result Proceed to
      DTC C1AED is output A
      No DTCs are output B

    B

    END (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] WAS DEFECTIVE)

    A

  15. REPLACE REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)


    1. Replace the rear center ultrasonic sensor (RLC sensor) with a known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  16. CHECK DTC OUTPUT (C1AED)


    1. Clear the DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
      Result
      Result Proceed to
      DTC C1AED is output A
      No DTCs are output B

    B

    END (REAR CENTER ULTRASONIC SENSOR [RLC SENSOR] WAS DEFECTIVE)

    A

  17. REPLACE REAR CORNER ULTRASONIC SENSOR (RL SENSOR)


    1. Replace the rear corner ultrasonic sensor (RL sensor) with a known good one.

      Click here

      Tech Tips

      All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.

      Result
      Proceed to
      NEXT

    NEXT

  18. CHECK DTC OUTPUT (C1AED)


    1. Clear the DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > IPA/ICS/Clearance Sonar > Trouble Codes
      Result
      Result Proceed to
      DTC C1AED is output A
      No DTCs are output B

    A

    REPLACE CLEARANCE WARNING ECU ASSEMBLY for LHD: Click here
    REPLACE CLEARANCE WARNING ECU ASSEMBLY for RHD: Click here

    B

    END (REAR CORNER ULTRASONIC SENSOR [RL SENSOR] WAS DEFECTIVE)