Click here

AUDIO AND VISUAL SYSTEM, Diagnostic DTC:B15C3

Click here
Click here
DTC Code DTC Name
B15C3 Speaker Output Short
Click here

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

In addition, the radio receiver assembly detects a malfunction via the stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit

  • Harness or connector

  • Speakers

  • Stereo component amplifier assembly

  • DCM (telematics transceiver) (w/ Telematics Transceiver)
B004YFCE04
B004SJRE01
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Tip:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    2. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  2. Click here

    CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      for 12 Speakers A
      for 24 Speakers B

  3. Click here

    CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for LH Side

      *2: for RH Side

      *3: w/ Telematics Transceiver


    1. Disconnect the L52 stereo component amplifier assembly connector.

    2. Disconnect the H19*1 and/or H1*2 front No. 1 speaker assembly connector.

    3. Disconnect the G70*1 and/or G69*2 front No. 2 speaker assembly connector.

    4. Disconnect the G50 front No. 3 speaker assembly connector.

    5. Disconnect the K25*1 and/or K11*2 rear speaker assembly connector.

    6. Disconnect the K24*1 and/or K10*2 rear No. 2 speaker assembly connector.

    7. Disconnect the L15 rear No. 3 speaker assembly connector.

    8. Disconnect the G56 DCM (telematics transceiver) connector.*3

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 1. for LH Side:
      Tester Connection Condition Specified Condition
      L52-4 (WFL+) - H19-2 (+) Always Below 1 Ω
      L52-19 (WFL-) - H19-1 (-) Always Below 1 Ω
      L52-12 (FL+) - G70-2 (+) Always Below 1 Ω
      L52-27 (FL-) - G70-1 (-) Always Below 1 Ω
      L52-8 (TWL+) - K24-3 (+TW) Always Below 1 Ω
      L52-23 (TWL-) - K24-1 (-TW) Always Below 1 Ω
      K24-4 (+) - K25-2 (+) Always Below 1 Ω
      K24-2 (-) - K25-1 (-) Always Below 1 Ω
      L52-4 (WFL+) - Body ground Always 10 kΩ or higher
      L52-19 (WFL-) - Body ground Always 10 kΩ or higher
      L52-12 (FL+) - Body ground Always 10 kΩ or higher
      L52-27 (FL-) - Body ground Always 10 kΩ or higher
      L52-8 (TWL+) - Body ground Always 10 kΩ or higher
      L52-23 (TWL-) - Body ground Always 10 kΩ or higher
      K24-4 (+) - Body ground Always 10 kΩ or higher
      K24-2 (-) - Body ground Always 10 kΩ or higher
      Table 2. for RH Side (w/ Telematics Transceiver):
      Tester Connection Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G56-2 (SPI+) Always Below 1 Ω
      L52-28 (FR-) - G56-3 (SPI-) Always Below 1 Ω
      G56-5 (SPO+) - G69-2 (+) Always Below 1 Ω
      G56-6 (SPO-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K10-3 (+TW) Always Below 1 Ω
      L52-24 (TWR-) - K10-1 (-TW) Always Below 1 Ω
      K10-4 (+) - K11-2 (+) Always Below 1 Ω
      K10-2 (-) - K11-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      G56-5 (SPO+) - Body ground Always 10 kΩ or higher
      G56-6 (SPO-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      K10-4 (+) - Body ground Always 10 kΩ or higher
      K10-2 (-) - Body ground Always 10 kΩ or higher
      Table 3. for RH Side (w/o Telematics Transceiver):
      Tester Connection Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G69-2 (+) Always Below 1 Ω
      L52-28 (FR-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K10-3 (+TW) Always Below 1 Ω
      L52-24 (TWR-) - K10-1 (-TW) Always Below 1 Ω
      K10-4 (+) - K11-2 (+) Always Below 1 Ω
      K10-2 (-) - K11-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      K10-4 (+) - Body ground Always 10 kΩ or higher
      K10-2 (-) - Body ground Always 10 kΩ or higher
      Table 4. for Center Side:
      Tester Connection Condition Specified Condition
      L52-7 (CTR+) - G50-2 (+) Always Below 1 Ω
      L52-22 (CTR-) - G50-1 (-) Always Below 1 Ω
      L52-6 (WF1+) - L15-2 (+) Always Below 1 Ω
      L52-21 (WF1-) - L15-1 (-) Always Below 1 Ω
      L52-7 (CTR+) - Body ground Always 10 kΩ or higher
      L52-22 (CTR-) - Body ground Always 10 kΩ or higher
      L52-6 (WF1+) - Body ground Always 10 kΩ or higher
      L52-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  5. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  6. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear door speaker assembly.

      Click here

    2. Inspect the rear door speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  7. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  8. Click here

    CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

  9. Click here

    INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)


    1. B004XKIC35
      *a

      Component without harness connected

      (DCM [Telematics Transceiver])

      Remove the DCM (telematics transceiver).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (SPO+) - 2 (SPI+) Always Below 1 Ω
      6 (SPO-) - 3 (SPI-) Always Below 1 Ω
      5 (SPO+) - Body ground Always 10 kΩ or higher
      6 (SPO-) - Body ground Always 10 kΩ or higher
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

  10. Click here

    CHECK FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    • NGClick here
  11. Click here

    CHECK REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    • NG

      REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here

  12. Click here

    CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for LH Side

      *2: for RH Side

      *3: w/ Telematics Transceiver


    1. Disconnect the L52 and L54 stereo component amplifier assembly connector.

    2. Disconnect the H19*1 and/or H1*2 front No. 1 speaker assembly connector.

    3. Disconnect the G70*1 and/or G69*2 front No. 2 speaker assembly connector.

    4. Disconnect the G50 front No. 3 speaker assembly connector.

    5. Disconnect the N21*1 and/or N20*2 roof speaker assembly (front) connector.

    6. Disconnect the K25*1 and/or K11*2 rear speaker assembly connector.

    7. Disconnect the K23*1 and/or K9*2 rear No. 2 speaker assembly (rear door) connector.

    8. Disconnect the N23*1 and/or N22*2 roof speaker assembly (rear) connector.

    9. Disconnect the L14*1 and/or L13*2 rear No. 2 speaker assembly (rear tray) connector.

    10. Disconnect the L15 rear No. 3 speaker assembly connector.

    11. Disconnect the G56 DCM (telematics transceiver) connector.*3

    12. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 5. for LH Side:
      Tester Connection Condition Specified Condition
      L52-4 (WFL+) - H19-2 (+) Always Below 1 Ω
      L52-19 (WFL-) - H19-1 (-) Always Below 1 Ω
      L52-12 (FL+) - G70-2 (+) Always Below 1 Ω
      L52-27 (FL-) - G70-1 (-) Always Below 1 Ω
      L52-8 (TWL+) - K23-2 (+) Always Below 1 Ω
      L52-23 (TWL-) - K23-1 (-) Always Below 1 Ω
      L54-1 (ROL+) - N21-2 (+) Always Below 1 Ω
      L54-5 (ROL-) - N21-1 (-) Always Below 1 Ω
      L52-14 (RL+) - K25-2 (+) Always Below 1 Ω
      L52-29 (RL-) - K25-1 (-) Always Below 1 Ω
      L54-3 (R-L+) - N23-2 (+) Always Below 1 Ω
      L54-9 (R-L-) - N23-1 (-) Always Below 1 Ω
      L52-10 (SL+) - L14-2 (+) Always Below 1 Ω
      L52-25 (SL-) - L14-1 (-) Always Below 1 Ω
      L52-4 (WFL+) - Body ground Always 10 kΩ or higher
      L52-19 (WFL-) - Body ground Always 10 kΩ or higher
      L52-12 (FL+) - Body ground Always 10 kΩ or higher
      L52-27 (FL-) - Body ground Always 10 kΩ or higher
      L52-8 (TWL+) - Body ground Always 10 kΩ or higher
      L52-23 (TWL-) - Body ground Always 10 kΩ or higher
      L54-1 (ROL+) - Body ground Always 10 kΩ or higher
      L54-5 (ROL-) - Body ground Always 10 kΩ or higher
      L52-14 (RL+) - Body ground Always 10 kΩ or higher
      L52-29 (RL-) - Body ground Always 10 kΩ or higher
      L54-3 (R-L+) - Body ground Always 10 kΩ or higher
      L54-9 (R-L-) - Body ground Always 10 kΩ or higher
      L52-10 (SL+) - Body ground Always 10 kΩ or higher
      L52-25 (SL-) - Body ground Always 10 kΩ or higher
      Table 6. for RH Side (w/ Telematics Transceiver):
      Tester Conne ction Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G56-2 (SPI+) Always Below 1 Ω
      L52-28 (FR-) - G56-3 (SPI-) Always Below 1 Ω
      G56-5 (SPO+) - G69-2 (+) Always Below 1 Ω
      G56-6 (SPO-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K9-2 (+) Always Below 1 Ω
      L52-24 (TWR-) - K9-1 (-) Always Below 1 Ω
      L54-2 (ROR+) - N20-2 (+) Always Below 1 Ω
      L54-6 (ROR-) - N20-1 (-) Always Below 1 Ω
      L52-15 (RR+) - K11-2 (+) Always Below 1 Ω
      L52-30 (RR-) - K11-1 (-) Always Below 1 Ω
      L54-4 (R-R+) - N22-2 (+) Always Below 1 Ω
      L54-10 (R-R-) - N22-1 (-) Always Below 1 Ω
      L52-11 (SR+) - L13-2 (+) Always Below 1 Ω
      L52-26 (SR-) - L13-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      G56-5 (SPO+) - Body ground Always 10 kΩ or higher
      G56-6 (SPO-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      L54-2 (ROR+) - Body ground Always 10 kΩ or higher
      L54-6 (ROR-) - Body ground Always 10 kΩ or higher
      L52-15 (RR+) - Body ground Always 10 kΩ or higher
      L52-30 (RR-) - Body ground Always 10 kΩ or higher
      L54-4 (R-R+) - Body ground Always 10 kΩ or higher
      L54-10 (R-R-) - Body ground Always 10 kΩ or higher
      L52-11 (SR+) - Body ground Always 10 kΩ or higher
      L52-26 (SR-) - Body ground Always 10 kΩ or higher
      Table 7. for RH Side (w/o Telematics Transceiver):
      Tester Conne ction Condition Specified Condition
      L52-5 (WFR+) - H1-2 (+) Always Below 1 Ω
      L52-20 (WFR-) - H1-1 (-) Always Below 1 Ω
      L52-13 (FR+) - G69-2 (+) Always Below 1 Ω
      L52-28 (FR-) - G69-1 (-) Always Below 1 Ω
      L52-9 (TWR+) - K9-2 (+) Always Below 1 Ω
      L52-24 (TWR-) - K9-1 (-) Always Below 1 Ω
      L54-2 (ROR+) - N20-2 (+) Always Below 1 Ω
      L54-6 (ROR-) - N20-1 (-) Always Below 1 Ω
      L52-15 (RR+) - K11-2 (+) Always Below 1 Ω
      L52-30 (RR-) - K11-1 (-) Always Below 1 Ω
      L54-4 (R-R+) - N22-2 (+) Always Below 1 Ω
      L54-10 (R-R-) - N22-1 (-) Always Below 1 Ω
      L52-11 (SR+) - L13-2 (+) Always Below 1 Ω
      L52-26 (SR-) - L13-1 (-) Always Below 1 Ω
      L52-5 (WFR+) - Body ground Always 10 kΩ or higher
      L52-20 (WFR-) - Body ground Always 10 kΩ or higher
      L52-13 (FR+) - Body ground Always 10 kΩ or higher
      L52-28 (FR-) - Body ground Always 10 kΩ or higher
      L52-9 (TWR+) - Body ground Always 10 kΩ or higher
      L52-24 (TWR-) - Body ground Always 10 kΩ or higher
      L54-2 (ROR+) - Body ground Always 10 kΩ or higher
      L54-6 (ROR-) - Body ground Always 10 kΩ or higher
      L52-15 (RR+) - Body ground Always 10 kΩ or higher
      L52-30 (RR-) - Body ground Always 10 kΩ or higher
      L54-4 (R-R+) - Body ground Always 10 kΩ or higher
      L54-10 (R-R-) - Body ground Always 10 kΩ or higher
      L52-11 (SR+) - Body ground Always 10 kΩ or higher
      L52-26 (SR-) - Body ground Always 10 kΩ or higher
      Table 8. for Center Side:
      Tester Connection Condition Specified Condition
      L52-7 (CTR+) - G50-2 (+) Always Below 1 Ω
      L52-22 (CTR-) - G50-1 (-) Always Below 1 Ω
      L52-6 (WF1+) - L15-2 (+) Always Below 1 Ω
      L52-21 (WF1-) - L15-1 (-) Always Below 1 Ω
      L52-7 (CTR+) - Body ground Always 10 kΩ or higher
      L52-22 (CTR-) - Body ground Always 10 kΩ or higher
      L52-6 (WF1+) - Body ground Always 10 kΩ or higher
      L52-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  14. Click here

    INSPECT ROOF SPEAKER ASSEMBLY (FRONT)


    1. Remove the roof speaker assembly (front).

      Click here

    2. Inspect the roof speaker assembly (front).

      Click here

      Result
      Proceed to
      OK
      NG

  15. Click here

    INSPECT ROOF SPEAKER ASSEMBLY (REAR)


    1. Remove the roof speaker assembly (rear).

      Click here

    2. Inspect the roof speaker assembly (rear).

      Click here

      Result
      Proceed to
      OK
      NG

  16. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear door speaker assembly.

      Click here

    2. Inspect the rear door speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  17. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  18. Click here

    CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

  19. Click here

    INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)


    1. B004XKIC35
      *a

      Component without harness connected

      (DCM [Telematics Transceiver])

      Remove the DCM (telematics transceiver).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (SPO+) - 2 (SPI+) Always Below 1 Ω
      6 (SPO-) - 3 (SPI-) Always Below 1 Ω
      5 (SPO+) - Body ground Always 10 kΩ or higher
      6 (SPO-) - Body ground Always 10 kΩ or higher
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

  20. Click here

    CHECK FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    • NGClick here
  21. Click here

    CHECK FRONT NO. 3 SPEAKER ASSEMBLY


    1. Replace the front No. 3 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

    • NGClick here
  22. Click here

    CHECK REAR NO. 2 SPEAKER ASSEMBLY [REAR DOOR]


    1. Replace the rear No. 2 speaker assembly (rear door) with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (REAR NO. 2 SPEAKER ASSEMBLY [REAR DOOR] IS DEFECTIVE)

    • NGClick here
  23. Click here

    CHECK REAR NO. 2 SPEAKER ASSEMBLY [REAR TRAY]


    1. Replace the rear No. 2 speaker assembly (rear tray) with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (REAR NO. 2 SPEAKER ASSEMBLY [REAR TRAY] IS DEFECTIVE)

    • NG

      REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here