Click here

FRONT SHOCK ABSORBER(for AWD) INSTALLATION

Click here
Click here Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

Click here

PROCEDURE


  1. Click here

    INSTALL FRONT SHOCK ABSORBER ASSEMBLY LH


    1. B004UBS

      Install the nut.

      8.5 N*m 87 kgf*cm 75 in.*lbf
    2. B004XWCC01
      *a Depression

      Install the front lower coil spring insulator to the front shock absorber assembly LH.

      Note:

      When installing the front lower coil spring insulator, fit the insulator to the depression of the spring seat.

    3. B004Y6UN01

      Secure SST in a vise.

      09727-30022

    4. Attach the hooks of each SST arm across the diameter of the coil spring.

      CAUTION:

      • B004SCEC06
        *a Front Coil Spring Diameter

        Do not perform the work without checking to make sure that the claws of the hooks are securely engaged.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004RLX

        Do not install SST to the front coil spring unless its top and bottom hook distance is set to the widest condition.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004WRL

        Do not install SST when the distances between the SST arms or the number of coils of the coil spring between the hooks are not the same.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

    5. Install the stopper pins to the hooks of SST.

      CAUTION:
      B004SQC

      • Do not perform the work if the stopper pin is not securely installed.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

    6. Using SST, compress the coil spring.

      CAUTION:

      • B004VXE

        While compressing the spring, if the front coil spring starts to bend into a bow shape, do not continue the work.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004WO6

        Do not compress the springs so far that the coils of the springs touch each other.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004TTA

        Do not use an impact wrench.

      • The threads may be stripped, or the sudden compression may result in slack that causes the hooks to slip off, causing the spring to fly out and possibly resulting in injury.

      • B004XJPN04

        If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

      • If a stopper pin is removed, install SST as shown in the illustration.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      09727-00110
    7. B004V74C01
      *a Depression

      Install the front coil spring to the front shock absorber assembly LH.

      Note:

      Make sure that the end of the front coil spring is positioned in the depression of the front lower spring seat.

    8. Install the front spring bumper to the front suspension support assembly.

    9. B004VGTC01
      *a Identification Mark
      *b Protrusion

      Install the front upper coil spring insulator to the front suspension support assembly as shown in the illustration.

      Note:

      Align the identification mark on the front support assembly suspension LH with the protrusion on the upper part of the front upper coil spring insulator LH.

    10. B004VW1

      Install the front suspension support assembly to the front shock absorber assembly LH.

      Note:

      Match the shape of the front shock absorber assembly support ring end to the shape of the front suspension support assembly.

    11. B004TIUC01
      *a Front Shock Absorber Assembly LH Claw
      *b End of Front Upper Coil Spring Insulator

      Turn the front suspension support assembly 120° or more to engage the end of the front upper coil spring insulator to the front shock absorber assembly LH claws.

      Note:

      • Make sure that the end of the front upper coil spring insulator is engaged securely to the 4 front shock absorber assembly LH claws.

      • Be careful not to deform the bellows of the front upper coil spring insulator.

      • Keep the front upper coil spring insulator free of oil and grease.

    12. Temporarily tighten a new lock nut.

    13. B004WBFC01
      *A for LH Side
      *B for RH Side
      *1 Front Lower Shock Absorber Bracket Sub-Assembly
      *a 60.8°+/-2°
      *b 29.2°
      B004SZX Front of the Vehicle

      Adjust the front suspension support assembly so that the bolts come to the positions as shown in the illustration, and remove SST from the front coil spring.

      Note:

      • Do not use an impact wrench. It will damage SST.

      • Make sure that the width across flat on the front shock absorber piston rod end is located parallel to the front shock absorber bushing.

      • Make sure of the direction of the front suspension support assembly when removing SST.

  2. Click here

    INSTALL FRONT LOWER SHOCK ABSORBER BRACKET SUB-ASSEMBLY LH


    1. Secure the front lower shock absorber bracket sub-assembly LH between aluminum plates in a vise.

      Note:

      Do not overtighten the vise.

    2. Install the front lower shock absorber bracket sub-assembly LH to the front shock absorber assembly LH with the bolt.

      48 N*m 489 kgf*cm 35 ft.*lbf
  3. Click here

    TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. B004XC5

      Install the front shock absorber with coil spring (upper side) with the 3 nuts.

      40 N*m 408 kgf*cm 30 ft.*lbf
    2. B004S5L

      Engage the guide to Connect the absorber control wire.

    3. Install the bolt.

      8.5 N*m 87 kgf*cm 75 in.*lbf

    4. Connect the connector.

    5. Install the front lower shock absorber bracket sub-assembly LH to the front lower suspension arm assembly LH.

    6. B004YEPC01
      *a Protrusion

      Align the protrusion of the front upper shock absorber bracket plate with cutout of the front lower shock absorber bracket sub-assembly LH, and temporarily install the nut.

      Tip:

      Fully tighten the nut after stabilizing the suspension.

  4. Click here

    INSTALL FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  5. Click here

    CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


    1. Connect the front height control sensor sub-assembly LH with the nut.

      5.4 N*m 55 kgf*cm 48 in.*lbf
  6. Click here

    INSTALL FRONT FLEXIBLE HOSE BRACKET LH


    1. Install the front flexible hose bracket LH to the front shock absorber with coil spring with the bolt.

      20 N*m 204 kgf*cm 15 ft.*lbf
  7. Click here

    INSTALL STEERING KNUCKLE LH

    Click here

  8. Click here

    STABILIZE SUSPENSION


    1. Install the front wheel.

    2. Lower the vehicle and bounce it up and down several times to stabilize the front suspension.

    3. Remove the front wheel.

    4. B004WXAC01
      *a Wooden Block
      *b Jack

      Jack up the front lower suspension arm assembly, and place a wooden block under it to avoid damage. Apply load to the suspension so that the front lower suspension arm assembly is placed in a horizontal position.

      CAUTION:
      B004TPQ

      • Do not raise the jack up too high.

      • The vehicle could fall, resulting in a serious accident.

      Note:

      • When jacking up the front lower suspension arm assembly, be sure to jack it up slowly.

      • Make sure to perform this operation with the vehicle kept as low as possible.

  9. Click here

    FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. B004SAW

      Fully tighten the front lower shock absorber bracket sub-assembly LH nut.

      112 N*m 1142 kgf*cm 83 ft.*lbf

    2. Fully tighten the lock nut.

      27.5 N*m 280 kgf*cm 20 ft.*lbf
      Note:

      Perform this step only when the front shock absorber with coil spring has been disassembled.

  10. Click here

    INSTALL FRONT SHOCK ABSORBER CAP LH


    1. B004T9H

      Install the front shock absorber cap LH.

  11. Click here

    INSTALL FRONT WHEEL

    Click here

  12. Click here

    INSTALL UPPER RADIATOR SUPPORT SEAL (for LH Side)

    Click here

  13. Click here

    INSTALL RADIATOR COVER PLATE (for RH Side)

    Click here

  14. Click here

    INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  15. Click here

    PERFORM INITIALIZATION

    Parking support brake system

    Click here
    Panoramic view monitor system

    Click here
    Parking assist monitor system

    Click here
    Automatic headlight beam level control system

    Click here
  16. Click here

    ADJUST HEADLIGHT AIMING

    Click here