FRONT SHOCK ABSORBER(for 2WD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SHOCK ABSORBER ASSEMBLY LH


    1. B004XWCC01
      *a Depression

      Install the front lower coil spring insulator to the front shock absorber assembly LH.

      Note

      When installing the front lower coil spring insulator, fit the insulator to the depression of the spring seat.

    2. B004Y6UN01

      Secure SST in a vise.

      SST
      09727-30022

    3. Attach the hooks of each SST arm across the diameter of the coil spring.

      CAUTION:


      • B004SCEC06
        *a Front Coil Spring Diameter

        Do not perform the work without checking to make sure that the claws of the hooks are securely engaged.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004RLX

        Do not install SST to the front coil spring unless its top and bottom hook distance is set to the widest condition.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004WRL

        Do not install SST when the distances between the SST arms or the number of coils of the coil spring between the hooks are not the same.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

    4. Install the stopper pins to the hooks of SST.

      CAUTION:


      • Do not perform the work if the stopper pin is not securely installed.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      B004SQC

    5. Using SST, compress the coil spring.

      CAUTION:


      • B004VXE

        While compressing the spring, if the front coil spring starts to bend into a bow shape, do not continue the work.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004WO6

        Do not compress the springs so far that the coils of the springs touch each other.

      • It could cause the hook to slip off and the spring to fly out, which could result in an injury.

      • B004TTA

        Do not use an impact wrench.

      • The threads may be stripped, or the sudden compression may result in slack that causes the hooks to slip off, causing the spring to fly out and possibly resulting in injury.

      • B004XJPN04

        If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

      • If a stopper pin is removed, install SST as shown in the illustration.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      SST
      09727-00110
    6. B004SNMC01
      *a Depression

      Install the front coil spring to the front shock absorber assembly LH.

      Note

      Make sure that the end of the front coil spring is positioned in the depression of the front lower spring seat.

    7. Install the front spring bumper to the front suspension support assembly.

    8. B004X79

      Install the front upper coil spring insulator to the front suspension support assembly as shown in the illustration.

    9. B004RJ5

      Install the front suspension support assembly to the front shock absorber assembly LH.

      Note

      Match the shape of the front shock absorber assembly support ring end to the shape of the front suspension support assembly.

    10. B004XZJC01
      *a Front Shock Absorber Assembly LH Claw
      *b End of Front Upper Coil Spring Insulator

      Turn the front suspension support assembly 120° or more to engage the end of the front upper coil spring insulator to the front shock absorber assembly LH claws.

      Note


      • Make sure that the end of the front upper coil spring insulator is engaged securely to the 4 front shock absorber assembly LH claws.

      • Be careful not to deform the bellows of the front upper coil spring insulator.

      • Keep the front upper coil spring insulator free of oil and grease.

    11. Temporarily tighten a new lock nut.

    12. B004TKSC02
      *A for LH Side
      *B for RH Side
      *a Identification Mark
      *b 120°
      *c 10.5°+/-2°
      B004SZX Front of the Vehicle

      Adjust the front suspension support assembly so that the bolts come to the positions as shown in the illustration, and remove SST from the front coil spring.

      Note


      • Do not use an impact wrench. It will damage SST.

      • Make sure that the width across flat on the front shock absorber piston rod end is located parallel to the front shock absorber bushing.

      • Make sure of the direction of the front suspension support assembly when removing SST.

  2. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. B004XC5

      Temporarily tighten the front shock absorber with coil spring (upper side) with the 3 nuts.

    2. B004X5DC01
      B004SZX Bolt
      B004UK4 Nut

      Temporarily tighten the front shock absorber with coil spring (lower side) to the front lower suspension arm assembly with the bolt and nut.

      Note


      • Insert the bolt from the rear of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Fully tighten the bolt after stabilizing the suspension.

  3. CONNECT STEERING KNUCKLE ASSEMBLY LH

    Click here

  4. CONNECT DISC BRAKE CYLINDER ASSEMBLY LH

    Click here

  5. CONNECT FRONT SKID CONTROL SENSOR WIRE LH


    1. B004REL

      Install the front skid control sensor wire LH with the nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  6. CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


    1. B004YLI

      Install the front height control sensor sub-assembly LH with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  7. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


    1. B004XO2

      Install the front stabilizer link assembly LH with the nut.

      Tech Tips

      If the ball joint turns together with the nut, use a 8 mm hexagon wrench to hold the stud bolt.

      Torque:
      125 N*m  { 1275 kgf*cm, 92 ft.*lbf }

  8. INSTALL ABSORBER CONTROL WIRE LH


    1. B004R3EC01
      B004SZX Bolt
      B004UK4 Nut
      B004XCB Connector

      Connect the clamp and 2 connectors.

    2. Install the absorber control wire LH with the bolt and nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  9. STABILIZE SUSPENSION


    1. Install the front wheel.

    2. Lower the vehicle and bounce it up and down several times to stabilize the front suspension.

    3. Remove the front wheel.

    4. B004Y3YC01
      *a Wooden Block
      *b Jack

      Jack up the front lower suspension arm assembly, and place a wooden block under it to avoid damage. Apply load to the suspension so that the front lower suspension arm assembly is placed in a horizontal position.

      CAUTION:


      • Do not raise the jack up too high.

      • The vehicle could fall, resulting in a serious accident.

      B004TPQ

      Note


      • When jacking up the front lower suspension arm assembly, be sure to jack it up slowly.

      • Make sure to perform this operation with the vehicle kept as low as possible.

  10. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. Install the front shock absorber with coil spring (upper side) with the 3 nuts.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

    2. Fully tighten the front shock absorber with coil spring bolt.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    3. Fully tighten the lock nut.

      Torque:
      27.5 N*m  { 280 kgf*cm, 20 ft.*lbf }

      Note

      Perform this step only when the front shock absorber with coil spring has been disassembled.

  11. INSTALL FRONT SHOCK ABSORBER CAP LH


    1. B004T9H

      Install the front shock absorber cap LH.

  12. INSTALL FRONT WHEEL

    Click here

  13. INSTALL UPPER RADIATOR SUPPORT SEAL (for LH Side)

    Click here

  14. INSTALL RADIATOR COVER PLATE (for RH Side)

    Click here

  15. CONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  17. PERFORM INITIALIZATION

    Parking support brake system

    Click here

    Panoramic view monitor system

    Click here

    Parking assist monitor system

    Click here

    Automatic headlight beam level control system

    Click here

  18. ADJUST HEADLIGHT AIMING

    Click here