Click here

FUEL FILTER REPLACEMENT

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel suction plate sub-assembly (fuel filter) removal/installation are shown below.

Table 1. Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point LKA/LDA system (for Mono camera type)
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*: When performing learning using the GTS. Click hereClick here
CAUTION:

  • B004WLP

    Never perform work on fuel system components near any possible ignition sources.

  • Vaporized fuel could ignite, resulting in a serious accident.


  • B004U4I

    Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

Note:

Do not try to remove the black nylon tube as it is welded to the fuel suction tube with pump and gauge assembly.

Click here

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

    Click here

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. Click here

    REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

    Click here

  4. Click here

    REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here

  5. Click here

    REMOVE NO. 1 FUEL SUB-TANK

    Click here

  6. Click here

    REMOVE FUEL PUMP FILTER

    Click here

  7. Click here

    REMOVE FUEL PUMP

    Click here

  8. Click here

    REMOVE FUEL MAIN VALVE ASSEMBLY

    Click here

  9. Click here

    REMOVE FUEL SUCTION PLATE SUB-ASSEMBLY (FUEL FILTER)


    1. B004XE8

      Detach the 2 claws to remove the No. 1 fuel suction support from the fuel suction plate sub-assembly (fuel filter).

      Note:

      Do not damage the fuel suction plate sub-assembly (fuel filter).

  10. Click here

    INSTALL FUEL SUCTION PLATE SUB-ASSEMBLY (FUEL FILTER)


    1. Attach the 2 claws to install the No. 1 fuel suction support to the fuel suction plate sub-assembly (fuel filter).

  11. Click here

    INSTALL FUEL MAIN VALVE ASSEMBLY

    Click here

  12. Click here

    INSTALL FUEL PUMP

    Click here

  13. Click here

    INSTALL FUEL PUMP FILTER

    Click here

  14. Click here

    INSTALL NO. 1 FUEL SUB-TANK

    Click here

  15. Click here

    INSTALL FUEL SENDER GAUGE ASSEMBLY

    Click here

  16. Click here

    INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

    Click here

  17. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here