Click here

SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P060E49

Click here
Click here
DTC Code DTC Name
P060E49 Internal Control Module Throttle Position Performance Internal Electronic Failure
Click here

MONITOR DESCRIPTION

The ECM monitors the signals received from the No. 1 throttle position sensor. As the ECM monitors the VTA1 signal of the No. 1 throttle position sensor, if these signals do not correlate, a DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060E49 Internal Control Module Throttle Position Performance Internal Electronic Failure

Either of the following conditions is met (1 trip detection logic):


  • ECM main CPU malfunction.

  • ECM sub CPU malfunction.

 ECM Comes on DTC stored SAE: P060E
Click here

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the GTS off.

  6. Turn the power switch off.

  7. Disconnect the GTS.

  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

  9. Connect the cable to the negative (-) auxiliary battery terminal.

  10. Connect the GTS to the DLC3.

  11. Turn the power switch on (IG).

  12. Turn the GTS on.

  13. With power switch on (IG) and wait for 16 seconds or more.

  14. Enter the following menus: Powertrain / Engine / Trouble Codes.

  15. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  17. Input the DTC: P060E49.

  18. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system is malfunctioning.

Click here

CAUTION / NOTICE / HINT

Note:

  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

  • After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

Tip:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      1. Powertrain > Engine > Clear DTCs


    5. Turn the power switch off.

      Result
      Proceed to
      NEXT

  2. Click here

    READ OUTPUT DTC (DTC P060E49)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Connect the GTS to the DLC3.

    4. Turn the power switch on (IG).

    5. Turn the GTS on.

    6. Wait 16 seconds or more.

    7. Enter the following menus: Powertrain / Engine / Trouble Codes.

    8. Read the DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTC P060E49 is output B