FRONT BUMPER DISASSEMBLY

PROCEDURE


  1. REMOVE FRONT BUMPER MOUNTING BRACKET


    1. B004ADFC01
      B004B1M Remove in this Direction

      Detach the 2 clips and remove the front bumper mounting bracket.

  2. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  3. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    1. B004A9X

      Remove the 2 screws.

    2. B004CRHC01
      B004B1M Remove in this Direction

      Detach the claws and guides and remove the radiator grille (or front panel) emblem.

  4. REMOVE FRONT BUMPER EXTENTION MOUNTING BRACKET


    1. B000TAU

      for Type A:


      1. Remove the 2 screws and front bumper extension mounting bracket.

    2. B000SHU

      for Type B:


      1. Remove the 2 screws and front bumper extension mounting bracket.

    3. B000RNN

      for Type C:


      1. Remove the 2 screws and front bumper extension mounting bracket.

  5. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY LH

    Click here

  6. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. REMOVE NO. 4 ENGINE ROOM WIRE

    Click here

  8. REMOVE FRONT CORNER ULTRASONIC SENSOR

    Click here

  9. REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER

    Click here

  10. REMOVE FRONT CENTER ULTRASONIC SENSOR

    Click here

  11. REMOVE ULTRASONIC SENSOR CLIP

    Click here

  12. REMOVE LOWER SIDE RADIATOR GRILLE LH


    1. B004CHGC01
      B004B1M Remove in this Direction

      Detach the claws and remove the lower side radiator grille LH.

  13. REMOVE LOWER SIDE RADIATOR GRILLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE FRONT BUMPER GARNISH LH

    B004CTWC01
    *1 Front Bumper Side Retainer
    B004B1M Remove in this Direction
    B004CG0 Protective Tape

    1. Apply protective tape around the front bumper garnish LH.

    2. Remove the 2 screws and front bumper side retainer.

    3. Detach the clips and claws and remove the front bumper garnish LH.

    4. Remove the protective tape.

  15. REMOVE FRONT BUMPER GARNISH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE HEADLIGHT WASHER COVER

    Click here

  17. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH

    Click here

  18. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE NO. 2 WASHER BRACKET

    Click here

  20. REMOVE WASHER BRACKET

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE NO. 1 FRONT BUMPER SIDE SUPPORT LH

    Tech Tips

    When removing the No. 1 front bumper side support LH, heat the front bumper cover and No. 1 front bumper side support LH using a heat light.

    Standard
    Item Temperature
    Front Bumper Cover 20 to 30°C (68 to 86°F)
    No. 1 Front Bumper Side Support LH

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B004AM0C40
    *a Heated Part
    *b Heat Light

    1. B004CVH

      Remove the No. 1 front bumper side support LH.

  22. REMOVE NO. 1 FRONT BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. REMOVE NO. 2 MOULDING TAPE

    Tech Tips

    When removing the No. 2 moulding tape, heat the front bumper cover and No. 2 moulding tape using a heat light.

    Standard
    Item Temperature
    Front Bumper Cover 20 to 30°C (68 to 86°F)
    No. 2 Moulding Tape

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B004AM0C40
    *a Heated Part
    *b Heat Light

    1. B000PVS

      Remove the No. 2 moulding tape.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  24. REMOVE FRONT BUMPER HOLE COVER LH


    1. B004B54C01
      B004B1M Remove in this Direction

      Detach the claws.

    2. Detach the anti-drop hook and remove the front bumper hole cover LH.

  25. REMOVE FRONT FENDER LINER RETAINER


    1. B004BQ8

      Detach the claw and remove the 3 front fender liner retainers.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  26. REMOVE RADIATOR GRILLE SUB-ASSEMBLY


    1. B004BN9

      Remove the 8 screws.

    2. Detach the claws and guides and remove the radiator grille sub-assembly.

      B004BWE

  27. REMOVE RADIATOR GRILLE MOULDING


    1. B004AHC

      Remove the 4 screws.

    2. B004BSZC02
      B004B1M Remove in this Direction

      Detach the claws and remove the radiator grille moulding.

  28. REMOVE NO. 2 RADIATOR GRILLE MOULDING


    1. B004AP8

      Remove the screw.

    2. B004ACWC01
      B004B1M Remove in this Direction

      Detach the claws and remove the No. 2 radiator grille moulding.

  29. REMOVE UPPER RADIATOR GRILLE


    1. B004AKY

      Remove the 2 screws.

    2. B004BYAC01
      B004B1M Remove in this Direction

      Detach the claws and remove the upper radiator grille from the lower radiator grille.

  30. REMOVE LOWER RADIATOR GRILLE

  31. REMOVE HEADLIGHT CLEANER HOSE


    1. B0049XFC03
      B004B1M Remove in this Direction

      Disconnect the headlight cleaner hose and drain the windshield washer fluid.

      Tech Tips

      Prepare a container before performing the procedure.

    2. B004CGJ

      Detach the clamps and remove the headlight cleaner hose.

  32. REMOVE NO. 2 DECK BOARD

    Click here

  33. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    B004CGW

    Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  34. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B004A52

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  35. REMOVE NO. 2 FRONT BUMPER MOUNTING BRACKET


    1. Check that the power switch off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      B004A52
    3. B004BN4

      Disconnect the 2 connectors of the pedestrian detection chamber assembly.

      Note

      When disconnecting any pedestrian detection chamber assembly connector, take care not to damage the pedestrian detection chamber assembly wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

        B004B1WC05
        *a Housing Lock *b CPA
        *c CPA Upper Part - -

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pedestrian detection chamber assembly connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B004BU8C21
        *a CPA *b Housing
        *c Correct *d Incorrect
    4. B004BYB

      Remove the 2 bolts.

    5. B004ABSC01
      B004B1M Remove in this Direction

      Detach the claws and guides and remove the No. 2 front bumper mounting bracket with the front bumper energy absorber.

  36. REMOVE PEDESTRIAN DETECTION CHAMBER ASSEMBLY

    Click here

  37. REMOVE FRONT BUMPER ENERGY ABSORBER

    Click here

  38. REMOVE HEADLIGHT ASSEMBLY LH

    Click here

  39. REMOVE HEADLIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  40. REMOVE LOWER ARM BRACKET BRACE SUB-ASSEMBLY LH

    B004C5LC01
    B004B1M Remove in this Direction

    1. Remove the 2 bolts and lower arm bracket brace sub-assembly LH.

  41. REMOVE LOWER ARM BRACKET BRACE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

    B0049XYC02
    B004B1M Remove in this Direction

    1. Remove the 8 bolts and front bumper reinforcement sub-assembly.