KNEE AIRBAG ASSEMBLY(for Driver Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

Tech Tips


  • Use the same procedure as for the RHD and LHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B004CGW

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B004A52

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE REAR CONSOLE BOX POCKET

    Click here

  5. REMOVE RADIO REMOTE TUNING SWITCH ASSEMBLY

    Click here

  6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

    Click here

  7. REMOVE SHIFTING HOLE COVER ASSEMBLY

    Click here

  8. REMOVE UPPER CONSOLE BOX

    Click here

  9. REMOVE BOX PANEL SUB-ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  11. REMOVE FRONT DOOR OPENING TRIM COVER LH

    Click here

  12. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH

    Click here

  13. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  14. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  15. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  16. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    B004AMOC01
    B004CG0 Deployment Side

    • When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

    • If the airbag deploys for any reason, it may cause a serious accident.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B004A52
    3. B004ARFC01
      *A for LHD
      *B for RHD
      *a Wire Harness Clamp

      Remove the 4 bolts.

    4. Detach the hooks and remove the lower No. 1 instrument panel airbag assembly.

    5. for LHD:


      1. Detach the wire harness clamp.

      2. Detach the claws to disconnect the DLC3.

    6. B004AUVC01
      *a Lock Button
      B004B1M Release in this Direction
      B004CG0 Protective Tape

      Tilt the lower No. 1 instrument panel airbag assembly toward the seat and support it with one hand.

    7. Using a screwdriver, release the lock button and disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      Tech Tips

      Tape the screwdriver tip before use.