FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front door lock assembly removal/installation are shown below.

Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

Front door inside panel sub-assembly Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Key-off operation function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • Procedure listed below is for the LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B004CGW

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B004A52

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT DOOR TRIM COVER SUB-ASSEMBLY LH (for Driver Side)

    Click here

  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Driver Side)

    Click here

  6. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY RH (for Front Passenger Side)

    Click here

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH (for Front Passenger Side)

    Click here

  8. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

    Click here

  9. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX

    Click here

  10. REMOVE NO. 1 FRONT DOOR HOLE COVER SUB-ASSEMBLY LH

    Click here

  11. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER LH

    Click here

  12. REMOVE FRONT DOOR DIVISION BAR SEAL LH

    Click here

  13. REMOVE FRONT DOOR INSIDE PANEL SUB-ASSEMBLY LH

    Click here

  14. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH


    1. B004B8QC01
      B004C4F "TORX" screw
      B004ANI Connector

      w/o Double Locking System:


      1. Disconnect the connector.

      2. Using a T30 "TORX" socket wrench, remove the 3 screws.

      3. B0049YV

        When reusing the front door lock with motor assembly LH:


        • Remove the door lock wire harness seal from the front door lock with motor assembly LH.

    2. B004C3RC01
      B004C4F "TORX" screw
      B004ANI Connector

      w/ Double Locking System:


      1. Disconnect the connector.

      2. Using a T30 "TORX" socket wrench, remove the 3 screws.

      3. B004CCX

        When reusing the front door lock with motor assembly LH:


        • Remove the door lock wire harness seal from the front door lock with motor assembly LH.

  15. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH


    1. w/o Double Locking System:


      1. B004CPLC01
        B004B1M Open in this Direction

        Using a screwdriver, detach the claws as shown in the illustration.

      2. B004A90

        Detach the claws to remove the front door lock cover sub-assembly LH.

    2. w/ Double Locking System:


      1. B004BTNC02
        B004B1M Open in this Direction

        Using a screwdriver, detach the claws as shown in the illustration.

      2. B004BFM

        Detach the claws to remove the front door lock cover sub-assembly LH.

  16. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B004CLQC01
      B004B1M Remove in this Direction

      w/o Double Locking System:


      1. Detach the clamp and remove the front door lock remote control cable assembly LH from the front door lock with motor assembly LH as shown in the illustration.

    2. B004BP8C01
      B004B1M Remove in this Direction

      w/ Double Locking System:


      1. Detach the clamp and remove the front door lock remote control cable assembly LH from the front door lock with motor assembly LH as shown in the illustration.

  17. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B004CO7C01
      B004B1M Remove in this Direction

      w/o Double Locking System:


      1. Detach the clamp and remove the front door inside locking cable assembly LH from the front door lock with motor assembly LH as shown in the illustration.

    2. B004ARXC01
      B004B1M Remove in this Direction

      w/ Double Locking System:


      1. Detach the clamp and remove the front door inside locking cable assembly LH from the front door lock with motor assembly LH as shown in the illustration.