CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door disassembly/reassembly are shown below.
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
---|---|---|---|
Disconnect cable from negative auxiliary battery terminal | Memorize steering angle neutral point | LKA/LDA system | |
Pre-collision system | |||
Parking assist monitor system | |||
Steering sensor zero point calibration | Variable gear ratio steering system | ||
|
Initialize power window control system |
|
Tech Tips
Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
Use the same procedure for the RH side and LH side.
The procedure described below is for the LH side.
PROCEDURE
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
REMOVE NO. 2 DECK BOARD
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
REMOVE FRONT DOOR TRIM COVER SUB-ASSEMBLY LH (for Driver Side)
Place Hand Here | |
Remove in this Direction |
Grasp the end of the front door trim cover sub-assembly LH and front door trim board sub-assembly LH and while pulling back, detach the clip.
Detach the remaining clips and remove the front door trim cover sub-assembly LH.
REMOVE COURTESY LIGHT ASSEMBLY LH (for Driver Side)
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Driver Side)
Remove the 2 screws.
Place Hand Here | |
Remove in this Direction |
Grasp the end of the front door trim board sub-assembly LH and front door inside panel sub-assembly LH and while pulling back, detach the clips.
Place Hand Here | |
Remove in this Direction |
Place your hands at the position shown in the illustration and pull to detach the clips.
Place Hand Here | |
Remove in this Direction | |
Lift Up in this Direction |
Place your hands at the position shown in the illustration and pull to detach the remaining clips, then lift up the front door trim board sub-assembly LH in the direction of the arrow and detach the guide.
Disconnect the connector.
Disconnect the front door lock remote control cable assembly LH from the front door inside handle sub-assembly LH and remove the front door trim board sub-assembly LH.
REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)
REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY RH (for Front Passenger Side)
Place Hand Here | |
Remove in this Direction |
Grasp the end of the front door assist grip assembly RH and front door trim board sub-assembly RH and while pulling back, detach the clip.
Place Hand Here |
Place your hands at the position shown in the illustration, detach the clips.
Place Hand Here |
Place your hands at the position shown in the illustration, detach the remaining clips and remove the front door assist grip assembly RH.
REMOVE COURTESY LIGHT ASSEMBLY RH (for Front Passenger Side)
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH (for Front Passenger Side)
Remove the 3 screws.
Place Hand Here | |
Remove in this Direction |
Grasp the end of the front door trim board sub-assembly RH and front door inside panel sub-assembly RH and while pulling back, detach the clips.
Remove in this Direction |
Place your hands at the position shown in the illustration and lift up the front door trim board sub-assembly RH in the direction of the arrow and detach the guide.
Disconnect the connector.
Disconnect the front door lock remote control cable assembly RH from the front door inside handle sub-assembly RH and remove the front door trim board sub-assembly RH.
REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Remove the 4 screws and front door inside handle sub-assembly LH.
REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Pull up the claws as shown in the illustration and remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH.
REMOVE INDICATOR LIGHT ASSEMBLY
REMOVE INDICATOR LIGHT BRACKET
REMOVE INDICATOR LIGHT COVER
REMOVE SEAT MEMORY SWITCH (for Driver Side)
REMOVE NO. 2 FRONT DOOR WIRE LH
Detach the clamps.
Disconnect the connector and remove the No. 2 front door wire LH.
REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Place Hand Here | |
Remove in this Direction |
Place your hands on the front door lower frame bracket garnish LH and pull to detach the clips and remove the front door lower frame bracket garnish LH.
REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX
REMOVE FRONT DOOR MULTIPLEX NETWORK ECU LH
Screw | |
Connector |
Disconnect the 3 connectors.
Remove the 2 screws and front door multiplex network ECU LH.
REMOVE NO. 1 FRONT DOOR HOLE COVER SUB-ASSEMBLY LH
REMOVE DOOR SIDE AIRBAG SENSOR LH
REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER LH
REMOVE FRONT DOOR DIVISION BAR SEAL LH
Using a clip remover, remove the 2 clips and front door division bar seal LH.
REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH
Using a clip remover, remove the 3 clips and front door No. 3 weatherstrip LH.
REMOVE FRONT DOOR WEATHERSTRIP LH
*a | Clip <A> |
Double-sided Tape |
Using a clip remover, detach the 3 clips <A>.
Remove the double-sided tape.
Detach the clips and remove the front door weatherstrip LH.
Clean the door panel.
REMOVE FRONT DOOR TRIM SEAL LH
Detach the clips and remove the front door trim seal LH.
REMOVE REAR ACCESS PANEL WEATHERSTRIP LH
*a | Clip <A> |
Double-sided Tape |
Using a clip remover, remove the clip <A>.
Detach the clips.
Remove the adhesional surface of the double-sided tape and rear access panel weatherstrip LH.
Clean the door panel.
REMOVE FRONT DOOR INSIDE PANEL SUB-ASSEMBLY LH
Remove in this Direction |
Insert a hand into the service hole and detach the snap lock and remove the door lock side rod as shown in the illustration.
Remove the bolt from the vehicle body.
Detach the claws and disconnect the front door wire LH.
Grommet | |
Connector |
Remove the grommet and disconnect the 2 connectors.
Open in this Direction |
Detach the claw and open the wire harness protector.
Disconnect the connector.
Detach the clamps.
"TORX" screw | |
Bolt | |
"TORX" bolt (w/ Rubber Cushion) |
|
Front Door Inside Panel Plate ("TORX" screw) |
Remove the 4 bolts.
Using a T30 "TORX" socket wrench, remove the 4 "TORX" bolts, 7 "TORX" screws and 3 front door inside panel plates.
Remove in this Direction |
Detach the center door guide piece of the arrow shown in the illustration and remove the front door inside panel sub-assembly LH together with the front door glass sub-assembly LH.
Note
Although CFRP material has high strength, there is a possibility of cracking if an excessive load is applied. As a result, pay attention to how it is handled.
Perform this operation with 2 or more people because of the risk of deformation or damage.
Be careful not to damage the front door glass sub-assembly LH.
REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH
REMOVE FRONT DOOR CHECK ASSEMBLY LH
Remove the 2 nuts and front door check assembly LH.
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Remove the 5 hole plugs.
Remove the 3 nuts.
Loosen the 2 nuts and remove the window regulator shims.
Remove in this Direction |
Lift up the glass in the direction shown in the illustration, loosen the bolt and remove the door window female stabilizer LH with the bolt.
Remove the 2 bolts.
Remove in this Direction (1) | |
Remove in this Direction (2) |
Pull out the front door upper glass stop of the front door glass sub-assembly LH from the front door upper window stop, slide the front and rear of the front door glass sub-assembly LH in the direction indicated by the arrows shown in the illustration to remove the front door glass sub-assembly LH.
Note
Do not damage the front door glass sub-assembly LH.
REMOVE FRONT DOOR UPPER WINDOW STOP
Remove the 2 front door upper window stops.
REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
Remove the 2 nuts and front door front lower frame sub-assembly LH.
REMOVE FRONT DOOR GLASS RUN LH
Remove the front door glass run LH from the front door front lower frame sub-assembly LH.
REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Nut | |
Connector |
Disconnect the connector and remove the 3 nuts.
Remove the 4 nuts and front door window regulator sub-assembly LH.
REMOVE FRONT DOOR WIRE LH
Detach the clamps and remove the front door wire LH.
REMOVE HOLE PLUG
for Front Door Inside Panel Side:
Remove the 2 hole plugs.
for Front Door Outer Panel Side:
Remove the hole plug.
REMOVE FRONT DOOR PANEL CUSHION
Detach the claws and remove the front door panel cushion.
REMOVE OUTSIDE DOOR HANDLE SUB-ASSEMBLY LH
Protective Tape |
Apply protective tape to the handle and door outer panel of the door outside handle sub-assembly LH to prevent damage.
Bolt | |
Connector |
Detach the clamp and disconnect the 4 connectors.
Remove the 4 bolts and outside door handle sub-assembly LH.
REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH
Using a T30 "TORX" socket wrench, remove the "TORX" screw.
Remove in this Direction |
Put the outside door handle in the full stroke position and remove the front door lock cylinder assembly LH.
REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH
REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH
*1 | Grommet |
Double-sided Tape |
Detach the grommet and adhesional surface of the double-sided tape.
Using a clip remover, detach the clips and remove the front door No. 2 weatherstrip LH.
Clean the door panel.
REMOVE STEP PANEL WIRE LH
Detach the clamps and remove the step panel wire LH.