REAR CROSSING TRAFFIC ALERT BUZZER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the blind spot monitor buzzer removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front Seat Assembly RH (Only for removal and installation)

  • Front Seat Assembly LH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

Tech Tips


  • Use the same procedure as for the RHD and LHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B004CGW

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. REMOVE REAR SEAT ASSEMBLY

    Click here

  5. REMOVE QUARTER INSIDE TRIM BOARD LH

    Click here

  6. REMOVE QUARTER INSIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  8. REMOVE REAR SEAT INNER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the rear No. 1 seat inner belt assembly LH.

  9. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  10. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE OUTER LAP BELT ANCHOR COVER

    Click here

  12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)

    Click here

  13. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  15. REMOVE QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

    Click here

  17. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE INNER ROOF SIDE GARNISH LH

    Click here

  19. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

    Click here

  21. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    Click here

  23. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER

    Click here

  25. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)

    Click here

  26. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. B004BP1C01
      B004B1M Remove in this Direction (1)
      B004CNL Remove in this Direction (2)

      Using moulding remover A, detach the claws.

    2. Detach the guide and while pulling toward the front of the vehicle, detach the No. 1 rear seat outer belt assembly RH belt guide.

      Tech Tips

      Use the same procedure for the other side.

    3. Place your hand at the position shown in the illustration and lift up the vehicle front side of the package tray trim panel assembly to detach the clips.

      B004A8IC01
      B0049X5 Place Hands Here B004B1M Release in this Direction
    4. B004BXN

      Disconnect the connector.

    5. Pull toward the front of the vehicle and detach the guides.

      B004AI0C01
      B004B1M Remove in this Direction - -

    6. Pass the rear No. 1 seat outer belt floor anchors through the package tray trim panel assembly and remove the package tray trim panel assembly.

  28. REMOVE BLIND SPOT MONITOR BUZZER


    1. B004CFX

      Disconnect the connector.

    2. Detach the clamp and remove the blind spot monitor buzzer.