RADIO ANTENNA CORD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the radio antenna cord removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front Seat Assembly RH (Only for removal and installation)

  • Front Seat Assembly LH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B004CGW

Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:

    B004A52

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Click here

    • f the airbag deploys for any reason, it may cause a serious accident.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  5. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. Detach the clamps and claws.

      B004B5W

    2. Disconnect the connector and remove the antenna cord sub-assembly.

  6. REMOVE REAR SEAT ASSEMBLY

    Click here

  7. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  8. REMOVE NO. 3 SPEAKER ASSEMBLY WITH BOX

    Click here

  9. REMOVE NO. 2 HYBRID BATTERY INTAKE DUCT


    1. B004B8G

      Detach the clips and remove the No. 2 hybrid battery intake duct.

  10. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Disconnect the 3 connectors.

      B0049YNC01
      B004C4F Bolt B004ANI Connector

    2. Remove the 3 bolts.

    3. Detach the clamps and remove the No. 2 antenna cord sub-assembly.

  11. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  12. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Click here

  13. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

  14. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. w/o Digital Audio Broadcasting Antenna:


      1. Disconnect the 2 connectors.

        B004BTL

      2. Detach the clamps and remove the No. 3 antenna cord sub-assembly.

    2. w/ Digital Audio Broadcasting Antenna:


      1. Disconnect the 3 connectors.

        B004A1XC01
        B004C4F Bolt B004ANI Connector

      2. Remove the bolt.

      3. Detach the clamps and remove the No. 3 antenna cord sub-assembly.

  15. REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY


    1. Disconnect the 2 connectors.

      B004BGP

    2. Detach the clamps and remove the No. 4 antenna cord sub-assembly.