LUGGAGE COMPARTMENT DOOR OPENER SYSTEM Luggage Compartment Door Opener does not Operate

DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the luggage compartment door opening switch assembly and operates the luggage compartment door lock assembly to open the luggage compartment door.

WIRING DIAGRAM

B0070ZVE07

CAUTION / NOTICE / HINT

Note


  • The luggage compartment door opener system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly)*, refer to Service Bulletin.


    • *: w/ Smart Entry and Start System

  • The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

    Click here


    • *: w/ Door Control Battery

PROCEDURE


  1. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. Check power door lock control system operation.

      Click here

      OK
      Power door lock control system is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Check wireless door lock control system operation.

      w/ Smart Entry and Start System: Click here

      w/o Smart Entry and Start System: Click here

      OK
      Wireless door lock control system is normal.
      Result
      Result Proceed to
      OK A
      NG (w/ Smart Entry and Start System) B
      NG (w/o Smart Entry and Start System) C

    B

    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System) Click here

    C

    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) Click here

    A

  3. PERFORM ACTIVE TEST USING GTS (Trunk and Back-Door Open)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Trunk and Back-Door Open Operate luggage compartment door lock assembly latch release OFF or ON -

      Body Electrical > Main Body > Active Test
      Tester Display
      Trunk and Back-Door Open
      OK
      Luggage compartment door lock assembly latch release motor operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY Click here

    OK

  4. READ VALUE USING GTS (Trunk/BDoor Open SW, Luggage Courtesy SW)


    1. Enter the following menus: Body Electrical / Main Body / Data List.

    2. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Trunk/BDoor Open SW Luggage compartment door opening switch signal OFF or ON

      OFF: Luggage compartment door opening switch off

      ON: Luggage compartment door opening switch on

      		 -
      Luggage Courtesy SW Luggage compartment door courtesy light switch signal OFF or ON

      OFF: Luggage compartment door courtesy light switch off

      ON: Luggage compartment door courtesy light switch on

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      Trunk/BDoor Open SW
      Luggage Courtesy SW
      OK
      The GTS display changes correctly in response to the ON/OFF operation of the luggage compartment door opening switch or luggage compartment door courtesy light switch.
      Result
      Result Proceed to
      OK (w/o Smart Entry and Start System) A
      OK (w/ Smart Entry and Start System) B
      NG (Trunk/BDoor Open SW) C
      NG (Luggage Courtesy SW) D

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY Click here

    D

    GO TO LIGHTING SYSTEM Click here

    B

  5. READ VALUE USING GTS (Tr/B-Door Unlock SW)


    1. Enter the following menus: Body Electrical / Entry&Start / Data List.

    2. Read the Data List according to the display on the GTS.


      Body Electrical > Entry&Start > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tr/B-Door Unlock SW Luggage electrical key switch OFF or ON

      OFF: Luggage electrical key switch not pressed

      ON: Luggage electrical key switch pressed

      		 When this item is abnormal, there is a malfunction in the luggage electrical key switch or related parts.
      OK
      The GTS display changes correctly in response to the operation of the luggage electrical key switch.
      Result
      Proceed to
      OK
      NG

    OK

    END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

    NG

    GO TO SMART ENTRY AND START SYSTEM (for Entry Function) Click here

  6. INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY


    1. Remove the luggage compartment door opening switch assembly.

      Click here

    2. Inspect the luggage compartment door opening switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY AND BODY GROUND)


    1. Disconnect the K53 main body ECU (multiplex network body ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K53-4 (TSW) - K42-5 Always Below 1 Ω
      K42-2 - Body ground Always Below 1 Ω
      K53-4 (TSW) or K42-5 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    1. Remove the luggage compartment door lock assembly.

      Click here

    2. Inspect the luggage compartment door lock assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)


    1. Disconnect the 3D instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      W3-3 (D+) - 3D-34 Always Below 1 Ω
      W3-1 (B) - 3D-20 Always Below 1 Ω
      W3-2 (E) - Body ground Always Below 1 Ω
      W3-3 (D+) or 3D-34 - Body ground Always 10 kΩ or higher
      W3-1 (B) or 3D-20 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Temporarily replace the instrument panel junction block assembly with a new or known good one.

      Click here

    2. Check that the luggage door opener system is normal.

      Result
      Proceed to
      OK
      NG

    OK

    END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here