LIGHTING SYSTEM ACC Signal Circuit

DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

B0071GIE02

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • First, check for smart entry and start system (for Start Function) DTCs, and after confirming that there is no malfunction, proceed with troubleshooting.*1

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

  • The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2

    Click here


    • *1: w/ Smart Entry and Start System

    • *2: w/ Door Control Battery

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Ignition switch ACC signal OFF or ON

      OFF: Ignition switch off

      ON: Ignition switch ACC

      		 "ON" is also displayed for this item when the ignition switch is ON.

      Body Electrical > Main Body > Data List
      Tester Display
      ACC SW
      OK
      Normal conditions listed above are displayed.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. Disconnect the 3F*1 or 3G*2 and 3B instrument panel junction block assembly connectors.

    2. Disconnect the K51 main body ECU (multiplex network body ECU) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      3F-1 - Body ground*1 Always 11 to 14 V
      3G-1 - Body ground*2 Always 11 to 14 V

      • *1: for LHD

      • *2: for RHD

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3B-3 - Body ground Always Below 1 Ω
      K51-19 (GND2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    B006YZPC23
    *A for LHD *B for RHD
    *a

    Component without harness connected

    (Instrument Panel Junction Block Assembly)

    		 - -

    1. Remove the instrument panel junction block assembly.

      Click here

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      3F-1 - MB-30 (ACC) Battery not connected to 3A-30 and 3B-3 10 kΩ or higher
      3F-1 - MB-30 (ACC)

      Battery positive (+) → 3A-30

      Battery negative (-) → 3B-3

      		 Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      3G-1 - MB-30 (ACC) Battery not connected to 3A-30 and 3B-3 10 kΩ or higher
      3G-1 - MB-30 (ACC)

      Battery positive (+) → 3A-30

      Battery negative (-) → 3B-3

      		 Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here