PARKING BRAKE ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. APPLY HIGH TEMPERATURE GREASE


    1. B004E2YC01
      B004FO9 High Temperature Grease

      Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.

  2. INSTALL PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY


    1. Install the parking brake anchor block sub-assembly and cable support bracket with the 2 nuts.

      Torque:
      75.5 N*m  { 770 kgf*cm, 56 ft.*lbf }
    2. Install the rear axle hub and bearing assembly.

      Click here

  3. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. Connect the No. 3 parking brake cable assembly with the nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
  4. INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY


    1. B004F8T

      Connect the No. 3 parking brake cable assembly to the parking brake shoe lever sub-assembly.

    2. B004EJ8C01
      *A LH Side
      *B RH Side
      *1 Parking Brake Anchor Block Sub-assembly
      *a Pin
      B004EIV High Temperature Grease

      Apply high temperature grease to the areas of the parking brake anchor block sub-assembly which make contact with the parking brake shoe lever sub-assembly.

      Note

      Check that the parking brake shoe lever sub-assembly is installed so that the pin is positioned as shown in the illustration.

    3. B004FC9C02
      *1 Parking Brake Shoe Lever Sub-assembly
      *a Parking Brake Inner Cable

      Check that the parking brake inner cable and parking brake shoe lever sub-assembly are securely connected by trying to pull them apart.

  5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. B004F8IN01

      Using SST, install the No. 1 parking brake shoe assembly with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011
  6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. B004E4LN01

      Using SST, install the No. 2 parking brake shoe assembly with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011
  7. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. B004FPWC01
      B004FO9 High Temperature Grease

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

    2. Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

  8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. B004E3DN01

      Using SST, install the parking brake shoe return tension spring.

      SST
      09703-30011
  9. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)


    1. B004GNKN01

      Using SST, install the parking brake shoe return tension spring.

      SST
      09703-30011
  10. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      B004GUAC01
      *A LH Side *B RH Side
      B004FMB Front of the Vehicle - -

      Note

      There should be no oil or grease on the friction surfaces of the shoe linings or discs.

  11. INSTALL REAR DISC

    Click here

  12. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  13. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  14. INSPECT PARKING BRAKE PEDAL TRAVEL

    Click here

  15. ADJUST PARKING BRAKE PEDAL TRAVEL

    Click here

  16. INSTALL REAR WHEEL

    Click here

  17. INSTALL ABS MOTOR RELAY


    1. With the power switch off, install the 2 ABS motor relays (ABS MOTOR NO. 1 relay and ABS MOTOR NO. 2 relay).

    2. Clear the DTCs.

      Click here