FRONT DOOR WINDOW FRAME MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

    Click here

  2. DISCONNECT FRONT DOOR WEATHERSTRIP


    1. B005N7D

      Disengage the 9 clips and disconnect the front door weatherstrip.

  3. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Tech Tips

    When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Front Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or moulding excessively.


    1. Using a heat light, heat the front door rear window frame moulding.

    2. B005LF0C02
      *a Double-sided Tape
      *b Caulking Sponge

      Using a moulding remover, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the front door rear window frame moulding.

  4. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    2. B005Q1IC07
      *a Tape

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement
      Area Measurement
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 6 rivets.

      B005N05

      CAUTION:

      Be careful of the drilled rivets, as they may be hot.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Disengage the guide and remove the front door upper window frame moulding from the door frame.

  5. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  6. REMOVE COWL SIDE TRIM BOARD

    Click here

  7. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING


    1. Disconnect each connector.

    2. Disengage each clamp.

    3. B005M4B

      Remove the 3 bolts and front door panel sub-assembly.

      Note

      To prevent damage, when removing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.

    4. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    5. B005Q1IC07
      *a Tape

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement
      Area Measurement
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    6. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 2 rivets and front door front window frame moulding.

      B005NK2

      CAUTION:

      Be careful of the drilled rivets, as they may be hot.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.