OCCUPANT DETECTION SENSOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during occupant detection sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-Crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

CAUTION:


  • B005NS4

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  2. REMOVE FRONT SEAT INNER BELT ASSEMBLY

    Click here

  3. DISCONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  4. REMOVE FRONT SEAT CUSHION SHIELD (for Standard Seat Type)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  5. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Standard Seat Type)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  6. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Sports Seat Type)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  7. REMOVE FRONT SEAT CUSHION SHIELD (for Sports Seat Type)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  8. REMOVE FRONT SEAT INNER CUSHION SHIELD

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  9. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Standard Seat Type)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  11. REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (for Standard Seat Type)


    1. A01VUWW

      w/o Variable Seat Cushion System:


      1. Remove the 6 hog rings.

    2. A01VU0Y

      w/ Variable Seat Cushion System:


      1. Remove the 2 hog rings.

    3. A01VWGB

      Remove the 18 hog rings and occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover.

  12. REMOVE OCCUPANT DETECTION SENSOR (FRONT SEAT CUSHION PAD WITH COVER) (for Sports Seat Type)


    1. w/ Seat Heater System:


      1. A01VUZ4

        Disconnect the connector.

      2. Disengage the 4 clamps.

    2. A01VXZ4

      Disconnect the connector.

    3. A01VX7Z

      Disengage the claw to separate the connector.

    4. Disengage the 10 hooks to remove the occupant detection sensor (separate type front seat cushion pad with cover).

      A01VV83