SEAT HEATER CONTROL(for Rear Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during seat heater control removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent Clearance Sonar System*1
Pre-crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and Start System

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power Door Lock Control System

Click here

Reset back door close position Power Back Door System

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:


  • B005NS4

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. REMOVE REAR SEAT ASSEMBLY RH (w/o Rear No. 2 Seat)

    for 60/40 Split Seat Type RH Side:

    Click here

  2. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/o Rear No. 2 Seat)


    1. for 60/40 Split Seat Type RH Side:


      1. B005N30

        Disengage the 2 hooks to disconnect the separate type rear seat cushion cover with pad.

      2. B005NDL

        Disconnect the 2 connectors.

      3. Disengage the 2 clamps to remove the seat heater control sub-assembly.

  3. REMOVE REAR SEAT ASSEMBLY LH (w/o Rear No. 2 Seat)

    for 60/40 Split Seat Type LH Side:

    Click here

  4. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/o Rear No. 2 Seat)


    1. for 60/40 Split Seat Type LH Side:


      1. B005OME

        Disengage the 2 hooks to disconnect the separate type rear seat cushion cover with pad.

      2. B005L9D

        Disconnect the 2 connectors.

      3. Disengage the 2 clamps to remove the seat heater control sub-assembly.

  5. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)

    for 60/40 Split Seat Type RH Side:

    Click here

  6. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)


    1. for 60/40 Split Seat Type RH Side:


      1. B005NNN

        Disengage the 2 hooks to disconnect the separate type rear seat cushion cover with pad.

      2. B005NLQ

        Disconnect the 2 connectors.

      3. Disengage the 2 clamps to remove the seat heater control sub-assembly RH.

  7. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)

    for 60/40 Split Seat Type LH Side:

    Click here

  8. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. for 60/40 Split Seat Type LH Side:


      1. B005N6L

        Disengage the 2 hooks to disconnect the separate type rear seat cushion cover with pad.

      2. B005OCO

        Disconnect the 2 connectors.

      3. Disengage the 2 clamps to remove the seat heater control sub-assembly LH.