SEAT HEATER SWITCH(for Rear Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat heater switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent Clearance Sonar System*1
Pre-crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and Start System

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power Door Lock Control System

Click here

Reset back door close position Power Back Door System

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:


  • B005NS4

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    Click here

  2. REMOVE REFRESHING SEAT SWITCH (w/o Rear No. 2 Seat)


    1. B005PGU

      Remove the 3 screws.

    2. Disengage the 2 guides to remove the refreshing seat switch.

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Click here

  4. REMOVE REAR SEATBACK COVER (w/ Rear No. 2 Seat)

    w/ Cover:

    Click here

  5. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY (w/ Rear No. 2 Seat)


    1. B005P1E

      Disengage the 2 hooks.

    2. B005NDE

      Disengage the 4 hooks.

    3. B005NCGC02
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 10 claws and 5 clips to remove the rear seatback board sub-assembly as shown in the illustration.

  6. REMOVE CENTER ARMREST HINGE COVER LH (w/ Rear No. 2 Seat)

    Click here

  7. REMOVE NO. 1 SEAT ARMREST ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  8. REMOVE ARMREST ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  9. REMOVE CENTER ARMREST HINGE COVER RH (w/ Rear No. 2 Seat)

    Click here

  10. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  11. REMOVE REAR SEAT CENTER ARMREST COVER (w/ Rear No. 2 Seat)

    Click here

  12. REMOVE CUP HOLDER ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  13. REMOVE REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  14. REMOVE NO. 2 REAR SEAT CENTER ARMREST BOX (w/ Rear No. 2 Seat)

    Click here

  15. REMOVE REAR SEAT HEATER SWITCH (w/ Rear No. 2 Seat)


    1. Disconnect the connector.

    2. B005OMU

      Remove the 3 screws and rear seat heater switch.