LUMBAR SUPPORT ADJUSTER ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lumbar support adjuster assembly removal/installation are shown below.

Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA /LDA system

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic view monitor system

Click here

Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

w/ occupant classification system


  • Front passenger seat

 Zero point calibration (Occupant classification system)

  • Occupant classification system

  • Passenger airbag ON/OFF indicator

  • Airbag system (Front passenger side)

  • Seat belt warning system (Front passenger)

Click here


  • Front seatback frame sub-assembly (driver seat)

  • Front seat adjuster assembly (driver seat)

  • Front seatback frame sub-assembly (front passenger seat)

  • Front seat adjuster assembly (front passenger seat)

 Initialize position control ECU Front Power Seat Control System (w/ Memory)

Click here

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. DISCONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY

    Click here

  3. REMOVE FRONT SEAT CUSHION SHIELD (for Standard Seat Type)

    Click here

  4. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Standard Seat Type)

    Click here

  5. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Sports Seat Type)

    Click here

  6. REMOVE FRONT SEAT CUSHION SHIELD (for Sports Seat Type)

    Click here

  7. REMOVE FRONT SEAT INNER CUSHION SHIELD

    Click here

  8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Click here

  9. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY

    Click here

  10. REMOVE FRONT SEAT HEADREST SUPPORT

    Click here

  11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Standard Seat Type)

    Click here

  12. REMOVE FRONT SEATBACK PAD WITH COVER (for Sports Seat Type)

    Click here

  13. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

    Click here

  14. REMOVE SEATBACK FELT

    Click here

  15. REMOVE FRONT SEATBACK EDGE PROTECTOR

    Click here

  16. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY


    1. w/o Variable Seat Cushion System:


      1. B005Q1Z

        Disconnect the lumbar support adjuster assembly connector.

      2. Disengage the clamp.

    2. w/ Variable Seat Cushion System:


      1. B005PVP

        Disengage the 2 clamps.

      2. B005OY5

        Disconnect the 2 lumbar support adjuster assembly connectors.

    3. B005NHE

      Disengage the 2 claws.

    4. Disengage the 2 guides to remove the lumbar support adjuster assembly from the front seatback frame sub-assembly.

  17. REMOVE FRONT SEATBACK HOOK

    Click here