SIDE AIRBAG SENSOR(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the door side airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B005PP8

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B005NWT

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

    Click here

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  6. REMOVE DOOR ARMREST COVER

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR NO. 1 TRIM BRACKET

    Click here

  11. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  12. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B005NWT

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        B005PTRC08
        *a White Housing Lock *b Yellow CPA
        *c Connector lock is released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    4. B005QH6

      Remove the nut and disengage the claw to remove the door side airbag sensor.

    5. After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

      B005OZVC05
      *a Incorrect *b Correct