SRS SEAT CUSHION AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat cushion airbag assembly RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Disconnect cable from negative battery terminal	Memorize steering angle neutral point	LKA/LDA System	Click here
		Pre-crash safety system
		Lighting system (EXT) Cornering lights
		Adaptive high beam system
	Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	Parking assist monitor system (w/ Parallel parking assist function)	Click here
		Parking assist monitor system (w/o Parallel parking assist function)	Click here
		Panoramic view monitor system	Click here
	Initialize back door lock	Power door lock control system	Click here
	Reset back door close position	Power back door system	Click here
Front passenger seat*1	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)	Click here
Front seatback frame sub-assembly (front passenger seat) Front seat adjuster assembly (front passenger seat)	Initialize position control ECU	Front power seat control system (w/ Memory)	Click here

*1: w/ Occupant Classification System

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here
Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

for Standard Seat Type:

If the front seat cushion airbag assembly RH has been deployed, replace the front seat cushion airbag assembly RH, front seat adjuster assembly RH, separate type front seat cushion pad and separate type front seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

Click here

for Sports Seat Type:

If the front seat cushion airbag assembly RH has been deployed, replace the front seat cushion airbag assembly RH, front seat adjuster assembly RH and front seat cushion pad with cover with the necessary parts in accordance with the extent of the collision damage.

Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The following procedure is for an LHD vehicle.

PROCEDURE

REMOVE FRONT SEAT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.

Click here
DISCONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE FRONT SEAT CUSHION SHIELD RH (for Standard Seat Type)

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD RH

Tech Tips

Use the same procedure as for the LH side.

for Standard Seat Type: Click here

for Sports Seat Type: Click here
REMOVE FRONT SEAT CUSHION SHIELD RH (for Sports Seat Type)

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE FRONT SEAT INNER CUSHION SHIELD RH

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD RH (for Standard Seat Type)

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE FRONT SEAT CUSHION PAD WITH COVER (for Sports Seat Type)

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE FRONT SEAT VERTICAL ADJUSTER ASSEMBLY RH (w/ Variable Seat Cushion System)

Tech Tips

Use the same procedure as for the LH side.

Click here
REMOVE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH
CAUTION:

When storing the front seat cushion airbag assembly RH, keep the airbag deployment side facing upward.

Deployment Side
1. Disengage the claw and clamp.
  
  Tech Tips
  
  Disengage the clamp first.
2. Disengage the clamp.
3. Remove the 3 nuts and front seat cushion airbag assembly RH.
  Note
  - Do not reuse the nuts.
  - Make sure that the front seat adjuster assembly RH is not deformed. If it is deformed, replace it with a new one.