REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during during rear door disassembly/reassembly are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Door window regulator assembly

  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B005QBF

      Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL


    1. Using a moulding remover A, disengage the claw as shown in the illustration.

      B005MHQC01
      B005M6U Insert Moulding Remover A Here - -

    2. While pulling the rear power window regulator switch assembly with rear door upper armrest base panel toward the rear of the vehicle, using a moulding remover A, disengage the claw as shown in the illustration.

      B005OMVC01
      B005M6U Insert Moulding Remover A Here - -

    3. Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.

  5. REMOVE REAR DOOR ARMREST COVER


    1. B005PHJ

      Remove the rear door armrest cover.

  6. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B005QCKC01
      B005M97 Protective Tape

      Apply protective tape to the rear door panel as shown in the illustration.

    2. B005LA0

      Remove the 3 screws.

    3. B005OQD

      Using a clip remover, disengage the 10 clips.

    4. w/o Rear Door Sunshade:


      1. B005O0S

        Disengage the 4 claws and guide.

    5. w/ Rear Door Sunshade:


      1. B005O0G

        Disengage the 2 claws and guide.

    6. Disconnect each connector.

    7. B005L4YC01
      B005OOA Remove in this Direction

      Disconnect the rear door lock remote control cable assembly from the rear door inside handle sub-assembly as shown in the illustration.

    8. B005MROC01
      B005OOA Remove in this Direction
      *a Push

      Disengage the 2 clamps.

    9. Disengage the 2 claws as shown in the illustration to disconnect the rear door inside locking cable assembly and remove the rear door trim board sub-assembly.

  8. REMOVE REAR DOOR LOCK CONTROL KNOB BEZEL


    1. B005OLHC01
      B005OOA Remove in this Direction

      Disengage the 2 claws and remove the rear door lock control knob bezel as shown in the illustration.

  9. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. B005OJGC01
      B005OOA Remove in this Direction

      Remove the rear door inner glass weatherstrip as shown in the illustration.

  10. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  11. REMOVE REAR NO. 2 SPEAKER ASSEMBLY

    Click here

  12. REMOVE REAR DOOR NO. 2 TRIM BRACKET


    1. B005MSI

      Remove the 2 screws and rear door No. 2 trim bracket.

  13. REMOVE REAR DOOR SERVICE HOLE COVER


    1. B005NQE

      Disconnect the connector.

    2. Disengage the clamp.

    3. Disengage the 9 clips to remove the rear door service hole cover.

  14. REMOVE REAR DOOR CHECK ASSEMBLY


    1. B005LX6C01
      B005NIZ Nut
      B005LWS Bolt

      Remove the 2 nuts, bolt and rear door check assembly.

  15. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)

    Tech Tips

    Use the same procedure for both curtain hooks.


    1. B005OQLC01
      *a Protective Tape
      B005M6U Insert Screwdriver Here

      Using a screwdriver with its tip wrapped with protective tape, push out the pin as shown in the illustration.

    2. B005OSF

      Disengage the 2 claws to remove the curtain hook.

  16. REMOVE REAR DOOR WEATHERSTRIP


    1. B005M6MC01
      *a Double-sided Tape

      Using a clip remover, disengage the 25 clips and remove the rear door weatherstrip.

  17. REMOVE REAR DOOR FRONT BELT SEAL


    1. B005PX6

      Remove the rear door front belt seal.

  18. REMOVE REAR DOOR GLASS RUN


    1. B005OJB

      Remove the rear door glass run.

  19. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. B005NZCC01
      B005NIZ Bolt
      B005LWS Screw

      Remove the 2 bolts, 2 screws and rear door window division bar sub-assembly.

  20. REMOVE REAR DOOR REAR GUIDE SEAL


    1. B005P5L

      Remove the 2 screws and rear door rear guide seal.

  21. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. B005NDS

      Remove the hole plug.

    2. Connect the rear power window regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the engine switch on (IG).

    5. Move the rear door glass sub-assembly so that the door glass bolts can be seen.

    6. Turn the engine switch off.

    7. Disconnect the cable from the negative (-) battery terminal.

    8. Disconnect the rear power window regulator switch assembly.

    9. B005MOR

      Remove the 2 bolts.

      Note

      Do not damage the rear door glass sub-assembly.

    10. B005MUSC01
      B005OOA Remove in this Direction (1)
      B005OMH Remove in this Direction (2)

      Remove the rear door glass sub-assembly as shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  22. REMOVE REAR DOOR FRAME GARNISH


    1. B005OAM

      Disengage the 3 claws to remove the rear door frame garnish.

  23. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. B005PJI

      Disengage the 2 claws to remove the rear door No. 2 service hole cover.

    2. B005PD6C02
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator assembly.

  24. REMOVE REAR DOOR LOCK ASSEMBLY

    Click here

  25. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. B005OBP

      Disengage the 2 claws.

    2. Using a screwdriver, disconnect the connector.

    3. B005OHBC01
      B005OOA Disengage in this Direction

      Disengage the 2 claws and move the lever as shown in the illustration.

    4. B005PTNC01
      B005OOA Remove in this Direction (1)
      B005OMH Remove in this Direction (2)

      Remove the rear door outside handle assembly as shown in the illustration.

  26. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. B005L1P

      Using a T30 "TORX" socket wrench, loosen the screw.

      Tech Tips

      The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

    2. Disengage the claw to remove the rear door outside handle cover.

  27. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B005Q9V

      Disengage the 3 claws to remove the rear door front outside handle pad.

  28. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B005LEV

      Disengage the claw.

    2. B005M98C02
      B005OOA Remove in this Direction (1)
      B005OMH Remove in this Direction (2)

      Disengage the 3 guides to remove the rear door rear outside handle pad as shown in the illustration.

  29. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B005P2AC01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the rear door outside handle frame sub-assembly to disengage the claw, and then remove it.

  30. REMOVE REAR DOOR PANEL CUSHION


    1. B005M1G

      Disengage the claw to remove the rear door panel cushion.

  31. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

    Click here

  32. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

    Click here

  33. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

    Click here

  34. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

    Click here

  35. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

    Click here

  36. REMOVE REAR DOOR OUTSIDE STRIPE

    Click here

  37. REMOVE REAR INNER BLACK OUT TAPE

    Click here

  38. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

    Click here

  39. REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

    Click here

  40. REMOVE REAR DOOR PANEL PROTECTOR


    1. B005OL8C01
      B005OOA Remove in this Direction
      B005M97 Double-sided Tape

      Disengage the 5 clips and remove the rear door panel protector as shown in the illustration.

  41. REMOVE REAR DOOR NO. 3 WEATHERSTRIP


    1. B005MN3C01
      B005M97 Double-sided Tape

      Disengage the claw and remove the rear door No. 3 weatherstrip.