DOOR CONTROL RECEIVER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during door control receiver removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Electrical key and tire pressure warning ECU and receiver

  • Register Transmitter ID

  • Initialize tire pressure warning system

  • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates

  • Tire pressure warning function

Click here for Registration

Click here for Initialization
*1: When performing learning using the GTS.
Click here Click here

Note

When replacing the electrical key and tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click here

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)

    Click here

  2. REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)

    Click here

  3. REMOVE REAR NO. 3 FLOOR BOARD (w/o Rear No. 2 Seat)

    Click here

  4. REMOVE SPARE WHEEL COVER (w/o Rear No. 2 Seat)

    for Compact Spare Tire:

    Click here

  5. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

    w/ Spare Tire:

    Click here

  6. REMOVE REAR FLOOR CARPET (w/o Rear No. 2 Seat)

    w/o Spare Tire:

    Click here

  7. REMOVE REAR NO. 4 FLOOR BOARD (w/o Rear No. 2 Seat)

    except Full Size Spare Tire:

    Click here

  8. REMOVE REAR NO. 4 FLOOR BOARD (w/o Rear No. 2 Seat)

    for Full Size Spare Tire:

    Click here

  9. REMOVE DECK FLOOR BOX RH (w/o Rear No. 2 Seat)

    w/o Spare Tire:

    Click here

  10. REMOVE DECK SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

    except Full Size Spare Tire:

    Click here

  11. REMOVE DECK SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

    for Full Size Spare Tire:

    Click here

  12. REMOVE REAR FLOOR FINISH PLATE (w/o Rear No. 2 Seat)

    Click here

  13. REMOVE REAR DOOR SCUFF PLATE RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  14. REMOVE REAR SEAT ASSEMBLY RH (w/o Rear No. 2 Seat)

    Click here

  15. REMOVE UPPER QUARTER TRIM PAD RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  16. REMOVE REAR SEAT SIDE GARNISH RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  17. REMOVE REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/o Rear No. 2 Seat)

    Click here

  19. REMOVE ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  20. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/o Rear No. 2 Seat)

    Click here

  21. REMOVE RECLINING REMOTE CONTROL BEZEL RH (w/o Rear No. 2 Seat)

    w/o Rear Power Seat System:

    Click here

  22. REMOVE FOLD SEAT SWITCH ASSEMBLY (w/o Rear No. 2 Seat)

    w/ Rear Power Seat System:

    Click here

  23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. 2 Seat)

    Click here

  24. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  25. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  26. REMOVE REAR DOOR SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  27. REMOVE REAR DOOR INSIDE SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  28. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH (w/ Rear No. 2 Seat)

    Click here

  29. REMOVE FRONT DECK SIDE TRIM COVER RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  30. REMOVE REAR SEAT SIDE GARNISH RH (w/ Rear No. 2 Seat)

    Click here

  31. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Rear No. 2 Seat)

    Click here

  32. REMOVE ROPE HOOK ASSEMBLY (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  33. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Rear No. 2 Seat)

    Click here

  34. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/ Rear No. 2 Seat)

    Click here

  35. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  36. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  37. REMOVE SMART DOOR CONTROL RECEIVER ASSEMBLY (w/o Tire Pressure Warning System)

    Note


    • Do not drop the smart door control receiver assembly, strike it with tools or subject it to impact.

    • If the smart door control receiver assembly is subjected to an impact, replace it with a new one.


    1. B005NB1

      Remove the bolt.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the smart door control receiver assembly.

  38. REMOVE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)

    Note


    • Do not drop the electrical key and tire pressure warning ECU and receiver, strike it with tools or subject it to impact.

    • If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.


    1. B005OKD

      Remove the bolt.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the electrical key and tire pressure warning ECU and receiver.