CAN COMMUNICATION SYSTEM Check Bus 5 Line for Short to +B

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 15 (CA5H) of the network gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the network gateway ECU and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 15 (CA5H) of the network gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the network gateway ECU and terminal 16 (BAT) of the DLC3.

  • Short in CAN main bus line

  • Short in CAN branch line

  • Certification ECU (smart key ECU assembly)

  • Combination meter mirror ECU (headup display) (w/ Headup Display System)

  • Headlight ECU sub-assembly LH

  • Combination meter assembly

  • Air conditioning amplifier assembly

  • Main body ECU (multiplex network body ECU)

  • Network gateway ECU

  • No. 5 CAN junction connector

WIRING DIAGRAM

B005PI6E01

CAUTION / NOTICE / HINT

Note


  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Drive the vehicle at a speed of 5 km/h (3 mph) or more for 32 seconds or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

Tech Tips


  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. CHECK FOR SHORT TO +B IN CAN BUS LINE (NETWORK GATEWAY ECU)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the J75 network gateway ECU connector.

      B005ON4C01
      *1 DLC3 - -
      *a

      Front view of wire harness connector

      (to Network Gateway ECU)

      		 - -

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J75-15 (CA5H) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      J75-16 (CA5L) - J12-16 (BAT)
      Result
      Result
      OK
      NG

    OK

    REPLACE NETWORK GATEWAY ECU Click here

    NG

  2. CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)


    1. Reconnect the J75 network gateway ECU connector.

    2. Disconnect the J97 No. 5 CAN junction connector.

      B005NLLC64
      *1 DLC3 - -
      *a

      Front view of wire harness connector

      (to No. 5 CAN Junction Connector)

      		 *b to Network Gateway ECU
      *c

      to Combination Meter Mirror ECU (Headup Display)

      (w/ Headup Display System)

      		 *d to Headlight ECU Sub-assembly LH
      *e to Main Body ECU (Multiplex Network Body ECU) *f to Air Conditioning Amplifier Assembly
      *g to Combination Meter Assembly *h to Certification ECU (Smart Key ECU Assembly)

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Connected to
      J97-1 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Network gateway ECU
      J97-12 (CANL) - J12-16 (BAT)
      J97-2 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter mirror ECU (headup display)*
      J97-13 (CANL) - J12-16 (BAT)
      J97-3 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Headlight ECU sub-assembly LH
      J97-14 (CANL) - J12-16 (BAT)
      J97-4 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
      J97-15 (CANL) - J12-16 (BAT)
      J97-5 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
      J97-16 (CANL) - J12-16 (BAT)
      J97-6 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
      J97-17 (CANL) - J12-16 (BAT)
      J97-7 (CANH) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)
      J97-18 (CANL) - J12-16 (BAT)
      *: w/ Headup Display System
      Result
      Result Proceed to
      OK A
      NG (Network gateway ECU main bus line) B
      NG (ECU or sensor CAN bus line) C

    A

    REPLACE NO. 5 CAN JUNCTION CONNECTOR

    B

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NETWORK GATEWAY ECU - NO. 5 CAN JUNCTION CONNECTOR)

    C

  3. CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)


    1. Reconnect all wire harness connectors.

    2. Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      B005NNFC01
      *1 DLC3 - -
      *a

      Component with harness connected

      (Network Gateway ECU)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      J75-15 (CA5H) - J12-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      J75-16 (CA5L) - J12-16 (BAT)

      Tech Tips

      If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

      Result
      Result
      OK
      NG

    OK

    REPLACE CORRESPONDING ECU OR SENSOR

    NG

    REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS LINE OR CONNECTOR