QUARTER WINDOW GLASS(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during quarter window assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-Crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  2. REMOVE DECK BOARD ASSEMBLY

    Click here

  3. REMOVE REAR NO. 3 FLOOR BOARD

    Click here

  4. REMOVE SPARE WHEEL COVER (for Compact Spare Tire)

    Click here

  5. REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)

    Click here

  6. REMOVE REAR FLOOR CARPET (w/o Spare Tire)

    Click here

  7. REMOVE REAR NO. 4 FLOOR BOARD (except Full Size Spare Tire)

    Click here

  8. REMOVE REAR NO. 4 FLOOR BOARD (for Full Size Spare Tire)

    Click here

  9. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)

    Click here

  10. REMOVE DECK FLOOR BOX RH (w/o Spare Tire)

    Click here

  11. REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

    Click here

  12. REMOVE DECK SIDE TRIM BOX RH (except Full Size Spare Tire)

    Click here

  13. REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)

    Click here

  14. REMOVE REAR FLOOR FINISH PLATE

    Click here

  15. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  16. REMOVE REAR SEAT ASSEMBLY LH

    Click here

  17. REMOVE UPPER QUARTER TRIM PAD LH

    Click here

  18. REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  19. REMOVE REAR FLOOR FINISH SIDE PLATE LH

    Click here

  20. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

    Click here

  21. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

    Click here

  22. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

    Click here

  23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Click here

  24. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

    Click here

  25. REMOVE QUARTER WINDOW ASSEMBLY


    1. B005NINC01
      B005M97 Protective Tape

      Apply protective tape to the area around the installation position of the quarter window assembly on the vehicle body to prevent it from being scratched.

    2. B005PZ5C01
      *a Piano Wire
      *b Clip

      Pass a piano wire between the vehicle body and quarter window assembly from the interior.

    3. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    4. Cut the adhesive by pulling the piano wire around the quarter window assembly.

      Note

      When separating the quarter window assembly, be careful not to damage the paint or interior and exterior ornaments.

    5. B005QGL

      Using suction cups, disengage the 4 clips and remove the quarter window assembly.

      Note

      Be careful not to drop the quarter window assembly.

  26. CLEAN VEHICLE BODY


    1. Clean and shape the contact surfaces of the vehicle body.


      1. B005LXJC01
        *a Vehicle Body
        B005M97 Adhesive

        Using a knife, cut off any excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

        Standard Dimension
        Area Dimension
        a 1.0 mm (0.0394 in.) or more

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with non-residue solvent.

      Tech Tips

      Even if all of the adhesive has been removed, clean the vehicle body.