SLIDING ROOF HOUSING(for Panoramic Moon Roof) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof glass sub-assembly, sliding roof housing panel, sliding roof drive gear assembly, sliding roof rail sub-assembly or sunshade trim sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-Crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Sliding roof ECU (sliding roof drive gear assembly)

  • Slide roof housing panel

  • Slide roof glass sub-assembly

 Initialize panoramic moon roof system (for Sliding Roof)

  • Auto operation function

  • Jam protection function

  • Key-off operation function

  • Wireless transmitter linked function

  • Sliding roof open warning function

Click here


  • Roof sunshade ECU (sliding roof drive gear assembly)

  • Sunshade trim sub-assembly

  • Slide roof rail sub-assembly

 Initialize panoramic moon roof system (for Roof Sunshade)

  • Auto operation function

  • Jam protection function

  • Key-off operation function

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

PROCEDURE


  1. REMOVE NO. 2 SLIDING ROOF SIDE GARNISH LH


    1. Move the sunshade trim sub-assembly to the fully opened position.

    2. B005P0O

      Remove the No. 2 sliding roof side garnish LH.

  2. REMOVE NO. 2 SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. REMOVE NO. 3 SLIDING ROOF SIDE GARNISH LH


    1. B005OWQ

      Remove the No. 3 sliding roof side garnish LH.

  4. REMOVE NO. 3 SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. REMOVE NO. 4 SLIDING ROOF SIDE GARNISH LH


    1. Move the sliding roof glass sub-assembly to the fully tilted up position.

    2. B005MTD

      Remove the No. 4 sliding roof side garnish LH.

  6. REMOVE NO. 4 SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY


    1. Move the sliding roof glass sub-assembly to the fully closed position.

    2. Using a T25 "TORX" socket wrench, remove the 6 screws and sliding roof glass sub-assembly.

      B005P7D

      Note

      To prevent the sliding roof glass sub-assembly and sliding roof drive gear assembly from becoming misaligned, move the sliding roof glass sub-assembly to the fully closed position before removing.

  8. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

  9. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH


    1. B005P6EC01
      B005NIZ Bolt
      B005LWS Nut

      Remove the 2 bolts, 2 nuts and front sliding roof housing mounting bracket LH.

  11. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH


    1. B005PDXC01
      B005NIZ Bolt
      B005LWS Nut

      Remove the 2 bolts, 3 nuts and center sliding roof housing mounting bracket LH.

  13. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH


    1. B005M60C01
      B005NIZ Bolt
      B005LWS Nut

      Remove the bolt, nut and rear sliding roof housing mounting bracket LH.

  15. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. REMOVE ROOF RACK ASSEMBLY LH

    Click here

  17. REMOVE ROOF RACK ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE SLIDING ROOF HOUSING ASSEMBLY


    1. Remove the 18 nuts.

      B005NAU

    2. Disengage the 2 guides and remove the sliding roof housing assembly.