ROOF HEADLINING(w/ Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  2. REMOVE DECK BOARD ASSEMBLY


    1. Remove the deck board assembly.

  3. REMOVE REAR NO. 4 FLOOR BOARD


    1. Remove the rear No. 4 floor board.

  4. REMOVE DECK SIDE TRIM BOX LH


    1. B005MIZ

      Disengage the 2 claws, 2 clips and 4 guides to remove the deck side trim box LH.

  5. REMOVE NO. 1 DECK BOARD


    1. B005NRN

      Disengage the 5 clips to remove the No. 1 deck board.

  6. DISCONNECT REAR NO. 2 SEAT ASSEMBLY


    1. B005ND1

      Using a clip remover, remove the 6 clips to disconnect the rear No. 2 seat assembly.

  7. REMOVE REAR DECK FLOOR BOX


    1. w/o Woofer:


      1. B005OS9

        Disengage the 6 claws to remove the rear deck floor box.

    2. w/ Woofer:


      1. B005MEE

        Disengage the 6 claws and clip to remove the rear deck floor box.

  8. REMOVE FRONT DECK FLOOR BOX


    1. w/o Spare Tire:


      1. B005NUA

        Disengage the 3 claws, clip and 2 guides to remove the front deck floor box.

    2. w/ Spare Tire:


      1. B005NYT

        Disengage the 3 claws, clip and 2 guides to remove the front deck floor box.

  9. REMOVE REAR FLOOR FINISH PLATE


    1. B005PN6C01
      B005OOA Remove in this Direction

      Disengage the claw as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    2. B005Q98C01
      B005OOA Remove in this Direction

      Disengage the 2 claws, 6 clips and 2 guides to remove the rear floor finish plate as shown in the illustration.

  10. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  11. REMOVE FRONT PILLAR GARNISH LH

    Click here

  12. REMOVE REAR DOOR SCUFF PLATE LH


    1. B005MF1

      Disengage the 5 claws, 3 clips and guide to remove the rear door scuff plate LH.

  13. REMOVE REAR DOOR INSIDE SCUFF PLATE LH


    1. B005OA7C02
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the claw as shown in the illustration.

      Tech Tips

      Use the same procedure for the front side and rear side.

    2. B005N5VC01
      B005OOA Remove in this Direction

      Disengage the 6 claws and 2 guides to remove the rear door inside scuff plate LH as shown in the illustration.

  14. REMOVE LOWER CENTER PILLAR GARNISH LH

    Click here

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  16. REMOVE CENTER PILLAR GARNISH LH

    Click here

  17. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  19. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  20. REMOVE REAR DOOR INSIDE SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  23. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

    Click here

  25. REMOVE REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

    Click here

  26. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  27. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. B005PFE

      Disengage the 2 claws and 2 guides to remove the front deck side trim cover LH.

  28. REMOVE REAR SEAT SIDE GARNISH LH


    1. B005MBK

      Using a clip remover, remove the clip.

    2. for LHD:


      1. B005LVM

        Disengage the 10 claws and 4 clips to remove the rear seat side garnish LH.

    3. for RHD:


      1. Disengage the 10 claws and 4 clips.

      2. Disconnect the connector to remove the rear seat side garnish LH.

  29. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

    Click here

  30. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. B005OJ6C01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and open the cover as shown in the illustration.

    2. Remove the bolt and rope hook assembly.

  31. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

    Click here

  32. REMOVE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  33. REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR

    Click here

  34. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. B005NA7C02
      B005NIZ Clip
      B005LWS Bolt

      Using a clip remover, remove the 2 clips.

    2. Remove the 3 bolts.

    3. Disengage the 6 claws and 3 clips.

      B005PEA

    4. Disconnect each connector to remove the deck trim side panel assembly LH.

  35. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

    Click here

  36. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Disengage the 2 claws and 10 clips to remove the roof side inner garnish assembly LH.

      B005P6U

    2. Remove the 10 clips from the roof side inner garnish assembly LH.

  37. REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH


    1. B005Q26

      Disengage the 3 clips to remove the rear roof side rail garnish assembly LH.

    2. Remove the 3 clips from the rear roof side rail garnish assembly LH.

  38. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  39. REMOVE REAR SEAT SIDE GARNISH RH


    1. B005LOR

      Using a clip remover, remove the clip.

    2. for LHD:


      1. B005MKO

        Disengage the 10 claws and 4 clips.

      2. Disconnect the connector to remove the rear seat side garnish RH.

    3. for RHD:


      1. Disengage the 10 claws and 4 clips to remove the rear seat side garnish RH.

  40. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Click here

  41. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  42. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

    Click here

  43. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. B005PDMC02
      B005NIZ Clip
      B005LWS Bolt

      Using a clip remover, remove the 2 clips.

    2. Remove the 2 bolts.

    3. Disengage the 6 claws and 3 clips to remove the deck trim side panel assembly RH.

      B005LT9

  44. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  45. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  46. REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  47. REMOVE ROOF CONSOLE BOX ASSEMBLY

    Click here

  48. REMOVE SPOT LIGHT ASSEMBLY

    Click here

  49. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

    Click here

  50. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  51. REMOVE RAIN SENSOR (w/ Rain Sensor)

    Click here

  52. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

    Click here

  53. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

    Click here

  54. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for all assist grip sub-assemblies.


    1. B005QD3C01
      *a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      SST
      09813-00010

      Note

      To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.

      Tech Tips

      Use the same procedure for the LH side and RH side.

    2. B005MEGC01
      *a 30 to 45°
      B005OOA Remove in this Direction

      Pull SST as shown in the illustration to disengage the claw.

      Note

      To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.

      Tech Tips


      • Use the same procedure for the claw on the other side of the assist grip cover LH.

      • Use the same procedure for the LH side and RH side.

    3. Remove the assist grip cover LH.

      Tech Tips

      Use the same procedure for the LH side and RH side.

    4. B005MA2C01
      B005OOA Remove in this Direction

      Disengage the 2 clips as shown in the illustration to remove the assist grip sub-assembly.

    5. Remove the 2 clips from the vehicle body.

  55. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the assist grip sub-assembly.

  56. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the assist grip sub-assembly.

  57. REMOVE VISOR BRACKET COVER LH

    Tech Tips

    Use the same procedure as for the visor bracket cover.

    Click here

  58. REMOVE VISOR ASSEMBLY LH

    Click here

  59. REMOVE VISOR HOLDER LH

    Tech Tips

    Use the same procedure as for the visor holder.

    Click here

  60. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  61. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  62. REMOVE VISOR HOLDER RH

    Tech Tips

    Use the same procedure as for the LH side.

  63. REMOVE ROOF HEADLINING ASSEMBLY


    1. for Windshield Glass Side:


      1. Disconnect each connector.

    2. for Front Pillar LH Side:


      1. Remove the protective cover.

      2. B005MFG

        Disengage the 4 clamps.

      3. Disconnect the 3 connectors.

      4. Install the protective cover.

    3. for Front Pillar RH Side:


      1. Remove the protective cover.

      2. B005OG7C02
        B005NIZ Connector
        B005LWS Washer Hose Assembly

        Disengage the 3 clamps.

      3. Disconnect the connector and washer hose assembly.

        Tech Tips

        Use a container to collect the windshield washer fluid.

      4. Install the protective cover.

    4. for Rear Pillar RH Side:


      1. B005NE9C02
        *A w/ Digital Audio Broadcasting Antenna or Digital Television Antenna
        B005NIZ Connector
        B005LWS Washer Hose Assembly

        Disengage the 2 clamps.

      2. Disconnect each connector and the washer hose assembly.

        Tech Tips

        Use a container to collect the windshield washer fluid.

    5. for Standard Roof:


      1. w/ Digital Television Antenna:


        1. Disconnect the connector.

          B005PY1C01
          *A w/ Digital Television Antenna - -

      2. Disengage the 10 claws, 3 clips and 2 fasteners to remove the roof headlining assembly.

    6. for Sliding Roof:


      1. Disconnect each connector.

        B005M2VC02
        *A w/ Digital Television Antenna - -
        *a Fastener *b Guide

      2. Disengage the 10 claws, 3 clips, 8 fasteners and guide to remove the roof headlining assembly.

    7. B005O0AC02
      B005OOA Remove in this Direction

      Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or vehicle interior.