NOISE FILTER(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during radio setting condenser removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Disconnect cable from negative battery terminal	Memorize steering angle neutral point	LKA/LDA System	Click here
		Intelligent clearance sonar system*1
		Pre-crash safety system
		Lighting system (EXT) Cornering lights
		Adaptive high beam system
	Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	Parking assist monitor system (w/ Parallel parking assist function)	Click here
		Parking assist monitor system (w/o Parallel parking assist function)	Click here
		Panoramic view monitor system	Click here
	Initialize back door lock	Power door lock control system	Click here
	Reset back door close position	Power back door system	Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

PROCEDURE

REMOVE TONNEAU COVER ASSEMBLY

Click here
REMOVE DECK BOARD ASSEMBLY

Click here
REMOVE REAR NO. 3 FLOOR BOARD

Click here
REMOVE SPARE WHEEL COVER (for Compact Spare Tire)

Click here
REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)

Click here
REMOVE REAR FLOOR CARPET (w/o Spare Tire)

Click here
REMOVE REAR NO. 4 FLOOR BOARD (except Full Size Spare Tire)

Click here
REMOVE REAR NO. 4 FLOOR BOARD (for Full Size Spare Tire)

Click here
REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)

Click here
REMOVE DECK FLOOR BOX RH (w/o Spare Tire)

Click here
REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

Click here
REMOVE DECK SIDE TRIM BOX RH (except Full Size Spare Tire)

Click here
REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)

Click here
REMOVE REAR FLOOR FINISH PLATE

Click here
REMOVE REAR DOOR SCUFF PLATE LH

Click here
REMOVE REAR SEAT ASSEMBLY LH

Click here
REMOVE UPPER QUARTER TRIM PAD LH

Click here
REMOVE REAR SEAT SIDE GARNISH LH

Click here
REMOVE REAR FLOOR FINISH SIDE PLATE LH

Click here
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Click here
REMOVE ROPE HOOK ASSEMBLY

Click here
REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Click here
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Click here
REMOVE RADIO SETTING CONDENSER
Note

When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.
1. Remove the bolt.
2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
3. Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.
4. Using a screwdriver, bend back and break off the claw as shown in the illustration.
5. Remove the terminal cover from the wire harness.
  Note
  - Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
  - Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
  - Check for deformation of the terminal after the wire harness has been removed from the terminal cover.