RADIO ANTENNA CORD(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Removal/installation of the spiral cable with sensor sub-assembly

  • Steering angle neutral point (Initialize parking assist monitor system)

  • Steering angle setting

 Parking assist monitor system (w/ Parallel Parking Assist Function)

Click here for Initialization

Click here for Calibration
Parking assist monitor system (w/o Parallel Parking Assist Function)

Click here for Initialization

Click here for Calibration
Steering angle neutral point (Initialize panoramic view monitor system) Panoramic view monitor system

Click here for Initialization

Click here for Calibration

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

PROCEDURE


  1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  2. REMOVE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) (for RHD)

    w/ Headup Display:

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  3. REMOVE NO. 1 HEATER TO REGISTER DUCT (for RHD)

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  4. REMOVE NO. 4 HEATER TO REGISTER DUCT

    Click here

  5. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT (for RHD)

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  6. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

    Click here

  7. REMOVE ION GENERATOR SUB-ASSEMBLY (for RHD)

    w/ Ion Generator:

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  8. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. w/ Navigation Antenna:


      1. B005PCG

        Disengage the 2 claws.

      2. Disconnect the connector.

    2. for LHD:


      1. Disengage each clamp and remove the antenna cord sub-assembly.

        B005LZ8C01
        *a w/ Navigation Antenna *b w/ Telematics Transceiver

    3. for RHD:


      1. Disengage each clamp and remove the antenna cord sub-assembly.

        B005LTIC01
        *a w/ Navigation Antenna - -

  9. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  10. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Remove the adhesive tape from the roof headlining assembly.

      w/o Television Antenna:

      B005L8AC01
      *A for Standard Roof *B for Sliding Roof
      *C for Panoramic Moon Roof - -
      *1 NO. 2 ANTENNA CORD SUB-ASSEMBLY *2 WASHER HOSE ASSEMBLY
      B005M97 Adhesive Tape B005LWS Front

      w/ Television Antenna:

      B005NDQC01
      *A for Standard Roof *B for Sliding Roof
      *C for Panoramic Moon Roof - -
      *1 NO. 2 ANTENNA CORD SUB-ASSEMBLY *2 WASHER HOSE ASSEMBLY
      B005M97 Adhesive Tape B005LWS Front

    2. Remove the No. 2 antenna cord sub-assembly from the roof headlining assembly.

  11. REMOVE BACK WINDOW UPPER PANEL TRIM

    Click here

  12. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. B005NBH

      Disengage each clamp.

    2. B005M64

      Disconnect each connector.

    3. B005NWP

      Disengage the 2 grommets and remove the No. 3 antenna cord sub-assembly.

  13. REMOVE NO. 5 ANTENNA CORD SUB-ASSEMBLY


    1. B005LC4

      Disconnect the connector.

    2. Disengage 4 clamps and remove the No. 5 antenna cord sub-assembly.

  14. REMOVE BACK DOOR TRIM COVER LH

    Click here

  15. REMOVE BACK DOOR TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. REMOVE BACK DOOR LOCK COVER

    Click here

  17. REMOVE BACK DOOR FINISH COVER LH (w/o Power Back Door)

    Click here

  18. REMOVE BACK DOOR FINISH COVER RH (w/o Power Back Door)

    Tech Tips

    Use the same procedure as for the LH side.

  19. REMOVE BACK DOOR TRIM BASE (w/ Power Back Door)

    Click here

  20. REMOVE DOOR PULL HANDLE (w/ Power Back Door)

    Click here

  21. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  22. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

    Click here

  23. REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY


    1. B005LH8

      Disconnect the connector.

    2. Disengage 4 clamps and remove the No. 4 antenna cord sub-assembly.