VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1405, C1406

DTC Code DTC Name
C1405 Open or Short in Front Speed Sensor RH Circuit
C1406 Open or Short in Front Speed Sensor LH Circuit

DESCRIPTION

Refer to DTCs C1413 and C1414.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1405 Open or Short in Front Speed Sensor RH Circuit

Either of the following is detected:


  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.

  2. With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.

  • Front speed sensor RH

  • Skid control ECU (brake actuator assembly)

  • Wire harness or connector

  • Front skid control sensor wire RH*

 -
C1406 Open or Short in Front Speed Sensor LH Circuit

Either of the following is detected:


  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.

  2. With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.

  • Front speed sensor LH

  • Skid control ECU (brake actuator assembly)

  • Wire harness or connector

  • Front skid control sensor wire LH*

 -

WIRING DIAGRAM

Refer to DTCs C1413 and C1414.

Click here

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

      Click here


      Chassis > ABS/VSC/TRC/EPB > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Speed Open Front speed sensor RH open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      FL Speed Open Front speed sensor LH open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -

      Chassis > ABS/VSC/TRC/EPB > Data List
      Tester Display
      FR Speed Open
      FL Speed Open
      OK
      Normal (There are no momentary interruptions.)

      Tech Tips

      Perform the above inspection before removing the sensor and connector.

      Result
      Result Proceed to
      OK A
      NG (w/o AVS) B
      NG (w/ AVS) C

    B

    CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR) Click here

    C

    INSPECT FRONT SKID CONTROL SENSOR WIRE Click here

    A

  2. READ VALUE USING GTS (FRONT SPEED SENSOR)


    1. Select the Data List using the GTS.

      Click here


      Chassis > ABS/VSC/TRC/EPB > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Wheel Speed Front wheel speed sensor RH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      		 Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FL Wheel Speed Front wheel speed sensor LH reading

      Min.: 0 km/h (0 mph)

      Max.: 326 km/h (202 mph)

      		 Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

      Chassis > ABS/VSC/TRC/EPB > Data List
      Tester Display
      FR Wheel Speed
      FL Wheel Speed

    2. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

      Tech Tips

      Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

      Click here

      OK
      The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
      Result
      Result Proceed to
      OK A
      NG (w/o AVS) B
      NG (w/ AVS) C

    B

    GO TO STEP 4 Click here

    C

    GO TO STEP 6 Click here

    A

  3. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC/EPB > Clear DTCs

    3. Turn the engine switch off.

    4. Start the engine.

    5. Perform a road test

    6. Check if the same DTC is recorded.

      Click here


      Chassis > ABS/VSC/TRC/EPB > Trouble Codes
      Result
      Result Proceed to
      DTCs C1405 and C1406 are not output. A
      DTCs C1405 and/or C1406 are output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)


    1. Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the A41 skid control ECU (brake actuator assembly) connector and the A93 and/or A92 front speed sensor connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A41-7 (FR+) - A93-3 (FR+) Always Below 1 Ω
      A41-6 (FR-) - A93-4 (FR-) Always Below 1 Ω
      A41-7 (FR+) or A93-3 (FR+) - Body ground Always 10 kΩ or higher
      A41-6 (FR-) or A93-4 (FR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A41-22 (FL+) - A92-3 (FL+) Always Below 1 Ω
      A41-21 (FL-) - A92-4 (FL-) Always Below 1 Ω
      A41-22 (FL+) or A92-3 (FL+) - Body ground Always 10 kΩ or higher
      A41-21 (FL-) or A92-4 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)


    1. B005MYFC02
      *A for RH
      *B for LH
      *a

      Front view of wire harness connector

      (to Front Speed Sensor)

      Reconnect the A41 skid control ECU (brake actuator assembly) connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Condition Specified Condition
      A93-3 (FR+) - Body ground Engine switch on (IG) 8 to 14 V
      for LH
      Tester Connection Condition Specified Condition
      A92-3 (FL+) - Body ground Engine switch on (IG) 8 to 14 V

      Note

      Check the speed sensor signal after replacement.

      Click here

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT SPEED SENSOR Click here

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  6. INSPECT FRONT SKID CONTROL SENSOR WIRE

    B005L5UC13
    *A for RH *B for LH
    *1 Front Skid Control Sensor Wire - -
    *a

    Front view of wire harness connector

    (to Sensor Side Connector)

    		 *b

    Front view of wire harness connector

    (to Vehicle Side Connector)

    1. Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Remove the front skid control sensor wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      z21-1 (FR+) - A91-3 (FR+) Always Below 1 Ω
      z21-1 (FR+) or A91-3 (FR+) - Body ground and other terminals Always 10 kΩ or higher
      z21-2 (FR-) - A91-4 (FR-) Always Below 1 Ω
      z21-2 (FR-) or A91-4 (FR-) - Body ground and other terminals Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      z20-1 (FL+) - A90-3 (FL+) Always Below 1 Ω
      z20-1 (FL+) or A90-3 (FL+) - Body ground and other terminals Always 10 kΩ or higher
      z20-2 (FL-) - A90-4 (FL-) Always Below 1 Ω
      z20-2 (FL-) or A90-4 (FL-) - Body ground and other terminals Always 10 kΩ or higher

      Note

      Check the speed sensor signal after replacement.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SKID CONTROL SENSOR WIRE Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SKID CONTROL SENSOR WIRE)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A41 skid control ECU (brake actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A41-7 (FR+) - A91-3 (FR+) Always Below 1 Ω
      A41-7 (FR+) or A91-3 (FR+) - Body ground Always 10 kΩ or higher
      A41-6 (FR-) - A91-4 (FR-) Always Below 1 Ω
      A41-6 (FR-) or A91-4 (FR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A41-22 (FL+) - A90-3 (FL+) Always Below 1 Ω
      A41-22 (FL+) or A90-3 (FL+) - Body ground Always 10 kΩ or higher
      A41-21 (FL-) - A90-4 (FL-) Always Below 1 Ω
      A41-21 (FL-) or A90-4 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)


    1. B005LR8C13
      *A for RH
      *B for LH
      *a

      Front view of wire harness connector

      (to Front Skid Control Sensor Wire)

      Reconnect the A41 skid control ECU (brake actuator assembly) connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Condition Specified Condition
      z21-1 (FR+) - Body ground Engine switch on (IG) 8 to 14 V
      for LH
      Tester Connection Condition Specified Condition
      z20-1 (FL+) - Body ground Engine switch on (IG) 8 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT SPEED SENSOR Click here

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here