TRANSFER CASE FRONT OIL SEAL(for RH Side) REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transfer case oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment

Perform the following procedures in the order shown:


  1. Clearing zero point calibration data and system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctioning

  • DTCs are output

  • Slip indicator light illuminated

  • ABS warning light illuminated

  • Theft deterrent system (tilt sensor) (w/ TFT Meter Type)

Click here

PROCEDURE


  1. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for 8AR-FTS)

    Click here

  2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for 2GR-FKS)

    Click here

  3. REMOVE NO. 3 ENGINE UNDER COVER (for 8AR-FTS)

    Click here

  4. REMOVE NO. 3 ENGINE UNDER COVER (for 2GR-FKS)

    Click here

  5. REMOVE FRONT FENDER APRON SEAL LH (for 8AR-FTS)

    Click here

  6. REMOVE FRONT FENDER APRON SEAL LH (for 2GR-FKS)

    Click here

  7. DRAIN AUTOMATIC TRANSAXLE FLUID (for U661F)

    Click here

  8. DRAIN AUTOMATIC TRANSAXLE FLUID (for U881F)

    Click here

  9. DRAIN TRANSFER OIL

    Click here

  10. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

    Click here

  11. REMOVE TRANSFER CASE OIL SEAL RH


    1. B005PFNC02
      *1 Transfer Case Oil Seal RH

      Using SST, remove the transfer case oil seal RH from the transfer case sub-assembly.

      SST
      09308-00010

      Note

      Do not damage the transfer case oil seal RH contact surface to the transfer case sub-assembly.

  12. INSTALL TRANSFER CASE OIL SEAL RH


    1. B005LE8C04
      *1 Transfer Case Oil Seal RH
      *a Depth

      Using SST and a hammer, install a new transfer case oil seal RH to the transfer case sub-assembly as shown in the illustration.

      SST
      09950-60010   ( 09951-00350, 09951-00580, 09952-06010 )
      09950-70010   ( 09951-07150 )
      Standard Depth
      33.5 to 34.5 mm (1.32 to 1.36 in.)

      Note


      • Tap in the transfer case oil seal RH uniformly so that the transfer case oil seal RH is straight.

      • Do not tap in the transfer case oil seal RH in too far.

    2. Apply a small amount of MP grease to the lip of the transfer case oil seal RH.

  13. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

    Click here

  14. ADD TRANSFER OIL

    Click here

  15. ADD AUTOMATIC TRANSAXLE FLUID (for U661F)

    Click here

  16. ADD AUTOMATIC TRANSAXLE FLUID (for U881F)

    Click here

  17. INSPECT FOR OIL LEAK

  18. INSTALL FRONT FENDER APRON SEAL LH (for 8AR-FTS)

    Click here

  19. INSTALL FRONT FENDER APRON SEAL LH (for 2GR-FKS)

    Click here

  20. INSTALL NO. 3 ENGINE UNDER COVER (for 8AR-FTS)

    Click here

  21. INSTALL NO. 3 ENGINE UNDER COVER (for 2GR-FKS)

    Click here

  22. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for 8AR-FTS)

    Click here

  23. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for 2GR-FKS)

    Click here