OIL LEVEL SENSOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine oil level sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point LKA /LDA system

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration

  • MIL illuminates / -

  • DTC P063051 is stored

Click here for 2GR-FKS (w/ Canister Pump Module)

Click here for 2GR-FKS (w/o Canister Pump Module)
ECU Communication ID Registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Gas leaks from exhaust system Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here for 2GR-FKS (w/ Canister Pump Module)

Click here for 2GR-FKS (w/o Canister Pump Module)

    w/ Canister Pump Module

  • Replacement of fuel injector assembly (for port injection)

  • Replacement of fuel injector assembly (for direct injection)

  • Replacement of fuel pump assembly (for high pressure side)

  • Replacement of ignition coil assembly

  • Air leaks from intake system

  • Gas leak from exhaust system is repaired

  • Replacement of knock control sensor

  • Replacement of Heated oxygen sensor

 Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here


    w/o Canister Pump Module

  • Replacement of fuel injector assembly (for port injection)

  • Replacement of fuel injector assembly (for direct injection)

  • Replacement of fuel pump assembly (for high pressure side)

  • Replacement of ignition coil assembly

  • Air leaks from intake system

  • Gas leak from exhaust system is repaired

  • Replacement of knock control sensor

 Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here

Replacement of automatic transaxle assembly

Perform the following procedures in the order shown:


  1. Reset Memory

  2. Input Transaxle Compensation Code into ECM

  3. Perform Road Test to Allow ECM to Learn

  • Large shift shock

  • Deterioration of fuel efficiency

for Initialization: Click here

for Registration: Click here

for Initialization: Click here

for Registration: Click here

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)

Perform the following procedures in the order shown:


  1. Reset Memory

  2. Input Transaxle Compensation Code into ECM

  3. Perform Road Test to Allow ECM to Learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)

Perform the following procedures in the order shown:


  1. Reset Memory

  2. Reset Transaxle Compensation Code

  3. Perform Road Test to Allow ECM to Learn
Front wheel alignment adjustment

  1. Clear zero point calibration data and store system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctions

  • DTCs are stored

  • Slip indicator light illuminates

  • ABS warning light illuminates

Click here

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/ Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here

Parking assist monitor system (w/o Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here


  • Parking assist ECU initialization

  • Adjust steering angle

 Panoramic view monitor system

for Initialization: Click here

for Calibration: Click here

Initialize headlight ECU sub-assembly LH

  • Adaptive high beam system

  • Automatic headlight beam level control system

Click here

PROCEDURE


  1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND

    Click here

  2. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

    Click here

  3. REMOVE OIL STRAINER SUB-ASSEMBLY

    Click here

  4. REMOVE ENGINE OIL LEVEL SENSOR


    1. Disconnect the engine oil level sensor connector.

    2. B005L4I

      Remove the clip from the engine oil level sensor.

    3. B005L64

      Remove the 2 bolts and engine oil level sensor.